Discount Products: Look through products available for a 25% – 50% discount in 2020. The items provided on a first come, first serve basis.
View Discounted Products

DC Power Supply

Showing 1–16 of 79 results


  • Unleash the power of modern, versatile, and sophisticated AC sources with our LSX Series – Programmable AC Power Source. These powerhouses come in single and three-phase options, ranging from 1.5kVA to 6kVA. Equipped with an advanced programmable controller featuring a vivid colour touchscreen interface, the LSX Series is not just cost-effective but also fully programmable for basic frequency conversion, advanced AC power line disturbance tests, and ATE applications.

     

    REQUEST A QUOTE
  • Key Features Provide Application Versatility

    • USB, LAN (LXI), IEEE-488.2 and RS-232C with SCPI compatibility
    • Compatible with PPSC Studio graphical user interface
    • LabVIEW for Windows®/LabWindows® drivers
    • Waveform Creation by Harmonic Synthesis
    • Waveform Capture (Voltage and Current)
    • Harmonic Analysis (Voltage and Current)
    • Metering of RMS and Peak Values
    • Continuous Self Calibration (CSC)
    • Line Sync
    • 6:1 Peak Current Capability
    • Low Impedance for EN61000-3-2, 3 Testing
    • Programmable Output Impedance
    • Up to 0-300 VAC Direct Coupled Out
    • 1 Phase / 3 Phase Switch Selectable
    • 15-5000 Hz Full Power Bandwidth
    • Power Levels from 500 VA to 6 kVA standard; 30kVA optional
    • Externally Referenced Meter Calibration
    • CE Safety & EMC and NTRL Safety Mark

     

    REQUEST A QUOTE
  • The AZX Series (Regenerative AC / DC Power Source) is a family of high power, single, split and three phase, AC, DC and AC+DC output capable Power Sources with full energy recovery to the AC mains when sinking power from the equipment under test. Available models range from 30 kVA to 440 kVA. Using a modern color touch screen based user interface for ease of use, the AZX Series is cost effective and fully programmable for both basic frequency conversion and advanced AC power line or DC power disturbance test applications requiring up to 1000 Hz fundamental frequency.

    The energy recovery capability allows both sourcing and sinking of current and power up to 100% of rated power. Adding the Load Option (Option L) adds full electronic regenerative AC & DC Load programming capability to the AZX.

     

    REQUEST A QUOTE
  • Key Performance Capabilities:

    • Up to 900 watts RMS power output (7136 model)
    • Small signal response up to 400 kHz
    • User-adjustable precision DC offset
    • User-adjustable current limit: 1A to 25A
    • 4-quadrant operation
    • AC/DC coupled

     

    REQUEST A QUOTE
  • with analogue and digital control, USB, RS232, LAN (LXI) and GPIB

    • Versatile solution for direct testing of dc power sources and PFCs
    • Constant current, resistance, conductance and power modes
    • Wide voltage and current range, 10 to 500V and 0 to 16A
    • 400 watts continuous dissipation at 28°C (360W at 40°C)
    • High resolution and accuracy for level setting
    • Built-in transient generator with variable slew
    • Current monitor output for waveform viewing
    • Variable drop-out voltage for battery testing
    • High resolution backlit graphic LCD with soft key control
    • Analogue remote control of levels and TTL control of on/off and transient switching
    • Front and rear input terminals
    • Load inputs rated to CAT II (300V)
    • Full bus control via USB, RS232, GPIB and LXI compliant LAN interfaces

     

    REQUEST A QUOTE
  • with analogue and digital control, USB, RS232, LAN (LXI) and GPIB

    • Versatile solution for direct testing of dc power sources and PFCs
    • Constant current, resistance, conductance and power modes
    • Wide voltage and current range, 10 to 500V and 0 to 16A
    • 400 watts continuous dissipation at 28°C (360W at 40°C)
    • High resolution and accuracy for level setting
    • Built-in transient generator with variable slew
    • Current monitor output for waveform viewing
    • Variable drop-out voltage for battery testing
    • High resolution backlit graphic LCD with soft key control
    • Analogue remote control of levels and TTL control of on/off and transient switching
    • Front and rear input terminals
    • Load inputs rated to CAT II (300V)
    • Full bus control via USB, RS232, GPIB and LXI compliant LAN interfaces

     

    REQUEST A QUOTE
    • Multiple ranges on each output for wider voltage/current choice
    • Four independent 105W full performance outputs
    • Instant individual on/off control plus sequencable multi on/off
    • Simultaneous display of meters and settings for all outputs
    • Up to 250 settings memories for individual or multiple outputs
    • Instant access to voltage/current setting for any output
    • USB, RS-232, LXI compliant LAN, and GPIB* interfaces (P versions)
    • USB, RS-232, LXI compliant LAN, and GPIB* interfaces (P versions)
      Duplicate power and sense terminals at rear (P versions)

     

    REQUEST A QUOTE
    • Proven member of a modular Power Module family, more than 800 units are in service
    • Precision-regulated Bi-Polar output provides up to +12 to -12 Amps for Magnet loads.
    • Smooth operation through zero amps output current, no “Crossover” problems.
    • All 2510 MCOR12 Power Modules are identical and interchangeable.
    • Has two high-precision measurements of output current;
      • one is used to close the regulation control loop,
      • provides an independent monitoring signal to the Crate Interface Card.
    • Fault sensing circuitry in the module sets a Fault Latch which inhibits the output.
    • A (momentary) Sync input signal inhibits MOSFET switching when it is active (high);
      • this eliminate switching noise .
      • reduces power line noise during sensitive analog signal measurements.

     

    REQUEST A QUOTE
    • Proven member of a modular Power Module family, more than 800 units are in service
    • Precision-regulated Bi-Polar output provides up to +30 to -30 Amps for Magnet loads.
    • Smooth operation through zero amps output current, no “Crossover” problems.
    • All 2510R30 MCOR30 Power Modules are identical and interchangeable
      • Programming Card is plugged into the replacement module.
    • Each channel has a critically-damped, LC noise filter with a cut-off frequency of about 8 kHz.
    • A 16-pin front panel diagnostics connector taps onto major circuit nodes which enables quick “inthe-crate” fault evaluation

     

    REQUEST A QUOTE
  • Enabling single-contact high-current/high-voltage test

    • Enables coaxial measurements up to 10,000 V and 300 A pulsed (600 A in a parallel configuration) with a single touchdown
    • Even distribution of high current with innovative multi-fingertip design
    • Compatible with Tesla 200/300 mm power device characterization system
    • Reduced measurement time by testing both high-voltage and high-current conditions with a single touchdown
    • Accurate characterization of a wide range of pad sizes and test currents, with minimum pad damage and contact resistance
    • Safe, reliable and repeatable high-current/voltage measurements over a wide temperature range (from -55°C to +300°C)

     

    REQUEST A QUOTE
  • Test power devices on wafer with high-performance and low-contact resistance on smaller pads

    • Minimal contact resistance at the pad-tip junction to reduce heating during measurements, with fewer probe marks
    • Measure devices on wafer at high-current conditions over a wide temperature range (-55°C to 300°C)
    • Small scrub minimizes damage on Al pad
    • Small footprint – tip for small pad probing down to 1 mm x 1 mm pad

     

    REQUEST A QUOTE
  • from 10,000 to 50,000 volts, 200 to 1,000 watts, with standard USB/LAN and Active PFC.

    • Rated voltage: 10kV, 30kV, 50kV
    • Encoder steps are programmable via the remote interface.
    • Output Power: 200Watt, 500Watt, 1,000Watt
    • Output Range0.1% to 100% of rated
    • Polarity : Fixed polarity, specify Positive (P), Negative (N)
    • Altitude : Operating: 6,500ft (2,000m)
    • Humidity : 0-80% at 0-31°C, linearly decreasing to 50% at 40°C

     

    REQUEST A QUOTE
  • Power Supply Outputs from 6V (@100A) to 600V (@1.3A)

    • High Power Density 750W in 1U half-rack size
    • Wide Range Input (85 – 265Vac Continuous)
    • Active Power Factor Correction (0.99 typical)
    • Output Voltage up to 600V, Current up to 100A
    • Built-in RS-232/RS-485 Interface Standard
    • Last Setting Memory; Front Panel Lockout
    • Advanced Parallel reports total current up to four identical units
    • Reliable Encoders for Voltage and Current Adjustment
    • Constant Voltage/Constant Current auto-crossover
    • Independent Remote ON/OFF and Remote Enable/Disable
    • External Analog Programming and Monitoring
    • Reliable Modular and SMT Design
    • Side-by-side mounting of two units in a 19” rack
    • Optional Interfaces
    • Isolated Analog Program /Monitor
    • IEEE Multi-Drop – SCPI
    • LAN Interface USB Interface
    • LabView® and LabWindows® drivers
    • Five Year Warranty

     

    REQUEST A QUOTE
  • • Active PFCPF of 0.94 for 3Φ
    • Built in RS232/RS485
    • Standard Multi-Drop (RS-485) Slave Interface
    • Global Commands for RS-232/RS-485
    • Last Setting Memory
    • High Resolution 16 bits ADCs & DACs
    • Reliable Encoders for Voltage and Current Adjustment
    • Parallel Operation with Active Current Sharing and Current Sum
    • Independent Remote ON/OFF and Remote Enable/Disable
    • External Analog Programming and Monitoring
    • Reliable Modular and SMT Design
    • Optional Isolated Analog Programming and Monitoring
    • Optional built-in GPIB (SCPI) Interface
    • Optional built-in LXI Compliant LAN interface
    • Optional built-in IEEE interface
    • Optional built-in Isolated Analog Programming
    • 19″ Rack mounted
    • Five Year Warranty
    • LabView® drivers/GUI
    • Worldwide Safety Agency Approvals
    • CE Mark for LVD and EMC Regulation

     

    REQUEST A QUOTE
    • Wide AC Input Voltage range for three-phase 208VAC, 400VAC and 480VAC Input.
    • High Power Factor (0.88 for Vout < 600V; 0.93 for Vout > 600V).
    • Built-In Protective functions (OVP, UVL, FOLD, OTP, AC-FAIL).
    • Output Isolation to 600V for Vout < 600V; to 1500V for Vout > 600V.
    • High Efficiency ( > 77% for Vout < 30V, > 88% for 30V < Vout < 600V, > 93.5% for Vout > 600V).
    • Rack-mount with provision for chassis slides; Zero-stacking for maximum power density.
    • Cooling Fan speed control (for reduced audible noise and longer life): Vout > 30V.
    • Light weight: < 97lbs (43kg) for Vout < 600V / < 70lbs (32kg) for Vout > 600V.
    • Dimensions: 5.25”/133mm: Height-3U x 19.00”/483mm: Width x 22.85”/581mm: Length
    • Fast Up/Down Programming Response Time (100ms/50ms for Vout < 600V, 17ms / 20ms for Vout > 600V).

     

    REQUEST A QUOTE
  • Wider AC Input Voltage range for 400VAC Input (342VAC – 440VAC).
    • Cooling Fan speed control (for reduced audible noise and longer life).
    • High Efficiency ( > 93%).
    • Fast Up/Down Programming Response Time (17ms / 20ms).
    • Output Isolation to 1500V.
    • Built-In Isolated J1 Remote Analog 5V/10V Program/Monitor.
    • Safe/Auto Re-Start and Last Setting Memory.
    • Built-In Protective functions (OVP, UVL, FOLD, OTP, AC-FAIL).
    • Two-Wire “Basic” and “Advanced” Parallel current share.
    • Built-in RS-232/RS-485 Multi-Drop Digital and Remote Analog Program/Monitor interfaces.
    • Optional LAN, GPIB and Isolated-Analog (4-20mA) Programming interfaces.
    • Lighter weight (< 70 lbs).

    imagesDatasheet

     

    REQUEST A QUOTE

Showing 1–16 of 79 results

Filters

 

Suppliers

Latest News