Products

A high-purity 20MHz DDS function generator designed for engineers requiring precision signal output, advanced modulation, and digital control.

Key Features:

• Frequency range: 0.001Hz to 20MHz
• High resolution: 6 digits or 1mHz
• Excellent stability (1ppm) and 10ppm one-year accuracy
• Digital control for phase-continuous sweep (linear or logarithmic)
• Output range: 5mV to 20V peak-to-peak from 50 or 600 Ohms
• Low distortion sine wave with high spectral purity
• Built-in modulation: AM, FSK, gated mode, tone switching
• Store and recall multiple instrument setups
• USB and RS232 interfaces for remote control

A high-performance 20MHz DDS function generator offering precise waveform control, high spectral purity, and flexible remote interfacing.

Key Features:

• Frequency range: 0.001Hz to 20MHz
• High resolution: 6 digits or 1mHz
• Frequency stability: ±1ppm, accuracy: ±10ppm
• Ultra-low distortion sine waves with high spectral purity
• Internal linear/log sweep with phase continuity
• Built-in AM, FSK, gated, and tone-switching modes
• Output: 5mV to 20V pk-pk from 50Ω or 600Ω
• Store and recall multiple instrument set-ups
• USB and RS232 interfaces for remote programming

High-performance dual-channel function and arbitrary waveform generator with up to 240 MHz output for advanced test and signal needs.

Key Features:

• Frequency range from 40 MHz to 240 MHz
• Dual independent or coupled full-performance channels
• Precise phase control: 0.001° resolution
• Arbitrary waveform support up to 800 MS/s
• Replay rates up to 80 MHz
• Wide range of built-in and user-defined waveforms
• Pulse generation up to 100 MHz, low jitter
• Internal/external modulation, sweep, gated, and burst modes
• USB, LAN (LXI compliant), and optional GPIB
• PC software for waveform generation and editing

Key Features:

• Single output up to 360W: Choose between 18V/20A or 35V/10A
• Mixed-mode regulation for high accuracy and low noise
• Fanless convection cooling for completely silent operation
• Bench or rack mountable, front and rear terminals
• OVP trip, high-resolution settings, and remote sense terminals
• P models offer USB, RS232, LAN interfaces (GPIB optional)
• Rotary, keypad, and step control for voltage and current
• Non-volatile memory for storing up to 25 user presets
• Seamless integration with Test Bridge software and automation systems

Single-phase, 2U, industrial amplifier/battery simulator

• Bench-sized
• Powered from 120V/230VAC
• Source and Sink (4 quadrant)
• Rugged Design
• 3-Year, No-Fault Warranty

Key Performance Capabilities:

• Drop outs and surges as fast as 1.2µs
• Small signal response up to 1 MHz
• 13.5 VDC at up to 28A
• Field-selectable ±40V, 75V or 150V potential

-60° to +200°C

• Economy model with high thermal capacity
• Precise temperatures with fast transitions from -60 to 200°C
• No annual leak testing required per EU 517/2014 F-Gas Regulation
• Effective testing and conditioning of electronic components, boards, and modules
• Available for 50 and 60Hz operation
• No need for Liquid Nitrogen (LN2) or Liquid Carbon Dioxide (LCO2)
• Remote communications and set up and touch screen operation
• User Defined Temperature Limits

Key Performance Capabilities:

• Slew rates up to 60 V/µsec.
• Up to 240A DC at +50VDC or –50VDC (4301-240 configuration).
• Can provide pulses of up to 800 amps at voltages of up to ±100V (4301-240 configuration).
• Adjustable compensation allows the system to maintain a 50V/2 µsec rise-time over a wide range of current outputs.

Key Performance Capabilities:

• Bandwidth: DC to 50 kHz
• Voltage: 0 to 250 V_RMS; 0 to 350 VDC
• Current: 100 to 500 A_RMS
• Distortion: 0.1%
• Power: 4 kW to 20 kW*Power levels up to 5X rated power when driving reactive loads
• High power efficiency and density

*Models available with output from 4 kW to 20 kW (capable of up to 125 kVA).

Key Performance Capabilities:

• 4-Quadrant – Can source and sink current
• ±80V – DC supply for 12V to 48V systems; meets 80V surge requirements
• 300 kHz Sine – DC ripple tests for all major standards
• 3µs Rise Time – Exceeds surge and dropout slew rate requirements
• 3mΩ DC Source Impedance – Out-performs ISO 7637-2 requirements
• Supports ground reference and supply offset testing required for ISO 16750-2 Sect. 4.8 and other similar standards

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +12 to -12 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510 MCOR12 Power Modules are identical and interchangeable.
• Has two high-precision measurements of output current;
  • one is used to close the regulation control loop,
  • provides an independent monitoring signal to the Crate Interface Card.
• Fault sensing circuitry in the module sets a Fault Latch which inhibits the output.
• A (momentary) Sync input signal inhibits MOSFET switching when it is active (high);
  • this eliminate switching noise .
  • reduces power line noise during sensitive analog signal measurements.

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +30 to -30 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510R30 MCOR30 Power Modules are identical and interchangeable
  • Programming Card is plugged into the replacement module.
• Each channel has a critically-damped, LC noise filter with a cut-off frequency of about 8 kHz.
• A 16-pin front panel diagnostics connector taps onto major circuit nodes which enables quick “inthe-crate” fault evaluation

• 2U Chassis – 19″ rack mount 3.48” Height, 9.60” Depth and Weight 6lb.
• Power 120V AC 60Hz
• Washable front removable air filter
• Ball Bearing AC fans provide 330 CFM
• Dual plenum design
• Cooling for 160mm,220mm depth modules
• Diverts lower warmed air to rear of Cabinet
• RM option diverts lower air to front of Cabinet

• accommodate these control schemes
• total control system interface on a single VME-standard card
• occupies the left-most slot of the crate
• monitoring voltage reference inputs, output voltages and fault conditions
• standard VMEbus-compatible 6U by 220 mm board installed
• Eurocard crate
• Two 96-pin I/O connectors

MCOR Modules

MCOR 2/6/9/12

Each module can be customized to provide maximum outputs of 2 amps, 6 amps, 9 amps, and 12 amps. Up to 16 of these can fit in a single 6U VME style crate.

MCOR 30

Each module can provide a maximum output 30 amps. Up to 8 of these can fit in a single 6U VME style crate.

• provides precision bi-polar output currents
• minimal zero-cross over distortion
• 19” rack mounted 6U x 220 mm crate
• crate has 17 slots; 16 (slot 0 thru 15)
• connectors
  • J1 (ExtIntlk),
  • J2 (CrateOK),
  • J3 (Input Reference Voltages),
  • J4 (Output Monitors), and
  • J9 (Bitbus)

High‐Resolution Portable TDR with Frequency‐Domain Analysis Tools

Ideal for testing all types of microwave/RF and digital cables and connectors

• Rugged portable TDR with S‐parameter tools
• Resolves connector detail (<1 cm)
• 75 μm (0.003 in.) cursor resolution
• 16‐bit digital sampling at up to 250 KSPS
• Stores thousands of TDR traces
• USB host/client, 10/100 Ethernet
• Lightweight, bright color screen
• Internet streaming and remote control