Products

• 150kHz to 3GHz (TGR2053) and 150kHz to 1.5GHz (TGR2051) frequency range
• High signal purity, phase noise <-117dBc/Hz (typical) at 1GHz output and 10kHz offset
• Amplitude range of -127dBm to +13dBm
• 0.1dBm amplitude setting resolution
• Internal or external analogue modulations (AM, FM, PM)
• Amplitude can be set in dBm, dBμV or in linear Volts.
• Internal or external digital modulations – ASK, OOK, FSK, 3FSK, 4FSK, GFSK, MSK, GMSK, HMSK & PSK with U01 option
• Modulation Synchronisation
• Fast amplitude and/or frequency sweeps with comprehensive triggering
• 5ms sweep settling time
• 1ppm frequency accuracy, <1ppm drift in first year
• Modulation waveform output on the rear panel
• Internal waveforms include: Sine, Square, Ramp, Triangle, PRBS (various lengths) and user-defined pattern
• Simple operation with the colour touch screen
• Programmable via USB, LAN (LXI) and GPIB (optional), SCPI compatible
• Compatible with previous Aim-TTi RF generators

The EMI 64k software allows to embed the TDEMI systems in a fully automated test environment.

• Full automation of EMI testing according to all commercial and military standards
• Automated control of turntable, antenna and other equipment
• Height and Angular Scan
• Procedures according to standards as well as customized procedures
• Reducing the cost for EMC and communication testing and certification by tailored packages

The measurement system for all emission measurments in the frequency range 1 Hz – 44 GHz.

• Frequency Range  1 Hz – 30MHz, 1GHz, 3GHz, 6GHz, 9GHz, 18GHz, 26GHz, 40 GHz and 44GHz
• 225 MHz Real-time Analysis Bandwidth
• Weighted Real-time Spectrogram up to 44 GHz
• CISPR Bandwidths 200 Hz, 9 kHz, 120 kHz, 1 MHz
• MIL/DO Bandwidths 10 Hz, 100 Hz, 1 kHz, 10 kHz, 100 kHz, 1 MHz

The measurement system for all emission measurments in the frequency range 1 Hz – 44 GHz.

• Full compliance EMI Reciever according to standard CISPR 16-1· 1, ANSI C63.2, MIL->461, and DO·160
• Spectrum Analyzer
• Integrated LOW Noise Ampllfier (lNAI)
• Integrated Preselect1on
• Tradttional and FFT·based Mode
• Automatic Stepped Attenuator
• Ultra Low Noise Floor
• Excellent spurious Performance
• Real-time Spectrum Analyzer optional
• Vast IQ-Bandwidth

TDEMI Mobile+. The ultra mobile EMI receiver – Emission measurements everytime, everywhere. Fully stand-alone operable.

• Frequency Ranges 10Hz – 1GHz, 3GHz, 6GHz or 7GHz
• 16000x faster than conventional receivers
• Super compact design and 12V supply
• 225 MHz fully gapless real-time analysis bandwidth
• Weighted Real-time Spectrogram

Ultra High Performance RT Spectrum Analyzer. Ultrafast EMI Measurements.

• Frequency Range from 1 Hz up to 50 GHz
• 225 MHz Real-time analysis bandwidth
• 100 dB Dynamic Range
• Ultrahigh performance preselection in all modes
• Up to 510 MHz Real-time IQ-Analysis bandwidth
• Ultra High Performance Spectrum Analyzer

Unleash the power of modern, versatile, and sophisticated AC sources with our LSX Series – Programmable AC Power Source. These powerhouses come in single and three-phase options, ranging from 1.5kVA to 6kVA. Equipped with an advanced programmable controller featuring a vivid colour touchscreen interface, the LSX Series is not just cost-effective but also fully programmable for basic frequency conversion, advanced AC power line disturbance tests, and ATE applications.

Key Features Provide Application Versatility

• USB, LAN (LXI), IEEE-488.2 and RS-232C with SCPI compatibility
• Compatible with PPSC Studio graphical user interface
• LabVIEW for Windows®/LabWindows® drivers
• Waveform Creation by Harmonic Synthesis
• Waveform Capture (Voltage and Current)
• Harmonic Analysis (Voltage and Current)
• Metering of RMS and Peak Values
• Continuous Self Calibration (CSC)
• Line Sync
• 6:1 Peak Current Capability
• Low Impedance for EN61000-3-2, 3 Testing
• Programmable Output Impedance
• Up to 0-300 VAC Direct Coupled Out
• 1 Phase / 3 Phase Switch Selectable
• 15-5000 Hz Full Power Bandwidth
• Power Levels from 500 VA to 6 kVA standard; 30kVA optional
• Externally Referenced Meter Calibration
• CE Safety & EMC and NTRL Safety Mark

The AZX Series (Regenerative AC / DC Power Source) is a family of high power, single, split and three phase, AC, DC and AC+DC output capable Power Sources with full energy recovery to the AC mains when sinking power from the equipment under test. Available models range from 30 kVA to 440 kVA. Using a modern color touch screen based user interface for ease of use, the AZX Series is cost effective and fully programmable for both basic frequency conversion and advanced AC power line or DC power disturbance test applications requiring up to 1000 Hz fundamental frequency.

The energy recovery capability allows both sourcing and sinking of current and power up to 100% of rated power. Adding the Load Option (Option L) adds full electronic regenerative AC & DC Load programming capability to the AZX.

• Customizable & savable test setups
• Program & Datalog Storage
• User Defined Temperature Limits
• Local & Remote Operations
• LabView™ drivers
• IEEE-488, RS232 ports

• 20 Amp Operation: Full performance with 20 amp service
• Automatic Power Reduction: Reduces power usage during idle periods
• Heat Only Mode: Reduces power usage when cold temperatures are not used
• WhisperStream Technology: quieter, smooth-sounding operation, 56 dBA
• Frost Free Test Environment: dry air purge for tester interface, prevents condensation:
  0.5 to 3scfm (0.25 to 1.5 l/s)
• Heated Defrost: quickly removes moisture buildup from internal chiller
• DUT Temperature Control : Proprietary control algorithm enables DUT temperature to be directly controlled
• Transition Rate*
  -55 to +125°C, approx. 10 seconds
  125 to -55°C, approx. 10 seconds
• System Airflow Output*
  4 to 18scfm (1.9 to 8.5 l/s) Continuous
• Temperature Range*
  -80 to +225°C (60Hz) No LN2 or LCO2 Required

• High reliability thermal cycling without thermoelectric modules
• Temperature range: -65 to 175°C
• Cooling power:
  • 40W at -40°C for lower power devices
  • 55W at -55°C and 120W at -40°C.
• Transition rate: up to <35 sec over 25 to -40°C
• Easy and secure thermal connection to in-circuit or test socked DUT
• Touch-screen controller: user-programmable temperatures, graphing, data logging
• Communications options: Ethernet, USB, IEEE, RS232

-60° to +200°C

• Economy model with high thermal capacity
• Precise temperatures with fast transitions from -60 to 200°C
• No annual leak testing required per EU 517/2014 F-Gas Regulation
• Effective testing and conditioning of electronic components, boards, and modules
• Available for 50 and 60Hz operation
• No need for Liquid Nitrogen (LN2) or Liquid Carbon Dioxide (LCO2)
• Remote communications and set up and touch screen operation
• User Defined Temperature Limits

1.5GHz & 3GHz

• 1.5GHz and 3GHz models
• Internal DDS baseband generator provided as logic LF output
• Compatible with previous Aim-TTi RF generators
• Phase noise <-117dBc/Hz (typ.) at 1GHz output 10kHz offset
• Extensive analog and digital modulations
• Amplitude range of -127dBm to +13dBm
• High signal purity
• Fast amplitude and/or frequency sweeps

Dual Measurement Bench Multimeter with USB and optional RS232, LXI/LAN and GPIB interfaces

1908 Digit Multimeter Series

• 1908
• 1908P

• Affordable 5.5 digit high performance bench/portable multimeter
• Dual display and dual measurement capability
• Mains power or Internal rechargeable batteries for true portability
• High accuracy and resolution: 0.02%, 1µV, 0.1µA, 1mΩ
• True RMS AC, Frequency, capacitance and temperature measurements
• Wide range of computing functions e.g. Ax + B
• USB interface standard, RS232, LAN/LXI and GPIB optional