Products

• Current measurement from insulated probing of conductor
• Suitable for observation and measurement of current in PCB tracks, component leads and ground planes
• Wide dynamic range of 10mA to 20A peak to peak
• Wide bandwidth of DC to 5MHz
• Low noise figure equivalent to <6mA rms at full B/W
• Safety rated to 300V Cat II (600V Cat 1)
• Suitable for connection to any oscilloscope
• High accuracy general purpose H-field probe
• Converts to ‘closed magnetic circuit’ current probe

• Customizable & savable test setups
• Program & Datalog Storage
• User Defined Temperature Limits
• Local & Remote Operations
• LabView™ drivers
• IEEE-488, RS232 ports

• 20 Amp Operation: Full performance with 20 amp service
• Automatic Power Reduction: Reduces power usage during idle periods
• Heat Only Mode: Reduces power usage when cold temperatures are not used
• WhisperStream Technology: quieter, smooth-sounding operation, 56 dBA
• Frost Free Test Environment: dry air purge for tester interface, prevents condensation:
  0.5 to 3scfm (0.25 to 1.5 l/s)
• Heated Defrost: quickly removes moisture buildup from internal chiller
• DUT Temperature Control : Proprietary control algorithm enables DUT temperature to be directly controlled
• Transition Rate*
  -55 to +125°C, approx. 10 seconds
  125 to -55°C, approx. 10 seconds
• System Airflow Output*
  4 to 18scfm (1.9 to 8.5 l/s) Continuous
• Temperature Range*
  -80 to +225°C (60Hz) No LN2 or LCO2 Required

• High reliability thermal cycling without thermoelectric modules
• Temperature range: -65 to 175°C
• Cooling power:
  • 40W at -40°C for lower power devices
  • 55W at -55°C and 120W at -40°C.
• Transition rate: up to <35 sec over 25 to -40°C
• Easy and secure thermal connection to in-circuit or test socked DUT
• Touch-screen controller: user-programmable temperatures, graphing, data logging
• Communications options: Ethernet, USB, IEEE, RS232

-60° to +200°C

• Economy model with high thermal capacity
• Precise temperatures with fast transitions from -60 to 200°C
• No annual leak testing required per EU 517/2014 F-Gas Regulation
• Effective testing and conditioning of electronic components, boards, and modules
• Available for 50 and 60Hz operation
• No need for Liquid Nitrogen (LN2) or Liquid Carbon Dioxide (LCO2)
• Remote communications and set up and touch screen operation
• User Defined Temperature Limits

The new G5.RSS series features

• High control dynamics
• An exceptional accuracy
• A nominal output voltage of up to 3000 VDC
• A wide current-voltage range with an auto-ranging factor of 3.
• You get the best value for your investment.

• compact and completely modular design
• high effectiveness in all operation modes, few requirements on building infrastructure
• ability to use an existing liquid cooling system directly
• optional matched liquid-to-air cooling unit TC.LAE available
• possibility of upgrading to systems of up to 1 MVA
• high level of system dynamics, ≤ 5 kHz modulation bandwidth
• non-restrictive capability of refeeding in the Q4 operation mode
• possibility of operating as an autonomous 4-Q and 3-phase quasi-analogue amplifier
• possibility of “Hardware-in-the loop”-operation (HIL mode)
• user friendly application software with pre-configured test patterns
• possibility of integrating into a complete SAS simulation and test system
• galvanic isolation available as an option without derating the simulator port data

Bidirectional (source & sink), Regenerative 0…65VDC to 0…1500VDC, 20kW up to 1.5 MW 

• cell system nominal voltage and type of chemistry
• number of cells
• internal resistance and associated parameters
• cell temperature progression
• allowed current
• charge efficiency
• energy computing and management facilities
• time-dependent and functional dependent parameters

• Setting of operational parameters for each output phase: (frequency, phase, voltage, basic waveform)
• Defining functional blocks enabling a wide variety of modulation capabilities
• Defining, editing and storing of even complex and long test sequences
• Preview window for output voltage waveforms
• LC load mode, definition of complex equivalent circuits
• Hand drawing curve tool and FOURIER tool (harmonics synthesis)
• TC.ACS provides an extensive safety concept in order to detect unwanted or off-limit conditions very quickly and to initiate controlled limiting or even a shutdown.

• compact and completely modular design
• high effectiveness in all operation modes, few requirements on building infrastructure
• ability to use an existing liquid cooling system directly
• optional matched liquid-to-air cooling unit TC.LAE available
• possibility of upgrading to systems of up to 1 MVA
• high level of system dynamics, ≤ 5 kHz modulation bandwidth
• non-restrictive capability of refeeding in the Q4 operation mode
• possibility of operating as an autonomous 4-Q and 3-phase quasi-analogue amplifier
• possibility of “Hardware-in-the loop”-operation (HIL mode)
• user friendly application software with pre-configured test patterns
• possibility of integrating into a complete SAS simulation and test system
• galvanic isolation available as an option without derating the simulator port data

• 16K Video Generator & Analyzer
• Dolby Vision™, HDR 10 and HDR 10+
• validating DP 1.4a & DP 2.0 Link Layer on DP Sinks and Sources
• Power Input +12 Vdc (AC/DC converter included)
• Module Size/Weight TBD for Weight and Size

• Compact sized DisplayPort™ 1.2 compliant Reference Sink
• HBR2 and MST capable Sink and Branch device
• Cerified as the platform for DP 1.2 LL CTS Ext1 tests
• Optional MST Debug panel and AUX Channel Monitor
• Debug and Test Controller GUI enables monitoring and previewing any MST stream
• User programmable EDID and DPCD

•  HDMI 2.1 Test Equipment (FRL)
• Enhanced Gaming Features (VRR, ALLM)
• FEC, Forward Error Correction
• HDCP 2.2 & HDCP 2.3 support  TMDS Support
• Dolby Vision™ Test Tool
• 8K@60 fps Support (12 Gbps/channel)
• eARC Support (end of 2019)
• DSC Support (ESTIMATED 2020)
• UCD Console GUI for debugging
• High level API for easy integreation

• Automated tests for USB-C™ DisplayPort™ Alt Mode
• Electrical Test to verify whole USB-C connector with single cable insert
• Test USB 2.0 and USB 3.0
• 4K@60 support
• Easily set test parameters with provided Software
• Easily run tests from the commandline
• Unigraf’s Test System Interface (TSI) Support
• Third Part Test Management Software
• Support e.g. NI TestStand Support

• UHD / 4K compliant test equipment
• HDMI 2.0 and DP 1.2 input and output in one unit
• DCP Approved HDCP 2.3 CTS Test Tool
• HDCP 1.3 and HDCP 2.3 support
• Sink and source video, audio and configuration parameters
• USB 3.0 connected
• UCD Console GUI for debugging
• High level API for easy integration

• Test DP over USB-C video and audio
• Test USB-C Power Delivery with DP Alt Mode
• DCP Apporved HDCP 2.3 CTS Tests
• Verify interface signal continuity
• 4K@60 support
• HDCP 1.3 and HDCP 2.3 support
• Capture video and audio, monitor and control interface parameters
• USB signal pass-thru
• UCD Console GUI for debugging
• High level API for easy integration