Products

The 3110A Standards Waveform Generator is a feature-rich, intuitive tool for engineers conducting EMC testing. From automotive to aviation applications, this unit simplifies the most complex test routines.

Key Features:

• 3,400+ Built-In Tests for automotive and industry standards
• Fast Rise Time: 3 µs full-scale with up to 1 MHz bandwidth
• Segment-Based Waveform Creation for custom sequences
• Free Lifetime Standards Updates
• Automated Triggering via GPIO or LAN
• Flexible Output Control including frequency, amplitude, and DC offset
• Extremely Precise Resolution: 0.01 Hz frequency, 76 µV amplitude
• Supports All Common Waveforms: Sine, square, triangle, DC, ripple, and more

The 7224 Linear Amplifier delivers power, speed, and precision in a compact 2U form factor. Designed for lab, test, and simulation environments, it provides outstanding performance for demanding applications.

Key Features:

• Up to 900W RMS output power
• Operates in controlled-current or controlled-voltage mode
• Field-configurable for low or high impedance loads
• DC to 1 MHz small signal bandwidth
• Produces up to 50A current or 158V peak
• Slew rate of 90 V/μs for sharp waveform reproduction
• Over-voltage, over-current, and over-temp protection circuits
• Compact 2U rack-mount or benchtop design
• Suitable for Helmholtz coil drivers, MRI/NMR, SMPS component testing

The 7548 Linear Amplifier is a high-output, low-noise solution engineered for precision and reliability in demanding environments.

Key Features:

• Up to 100 Ap / 195 Vp output
• Delivers 12,000W peak power for 40 ms
• Supports continuous 5,500W output into 1Ω load
• Operates from DC to 100 kHz bandwidth
• Field-selectable current or voltage mode
• Ideal for MIL-STD-704F three-phase testing
• Stackable for 800 Vp or 170 Ap system output
• Built-in protection against over-voltage, over-temp, and overload
• Intuitive LCD display and status indicators

7796HC Linear Power Amplifier – High Current DC & AC Precision

Key Features:

• Output up to 85A continuous, 200A in-rush current
• Frequency response: DC to 100+ kHz
• Four-quadrant operation: source and sink
• Field-selectable voltage or current modes
• Stable with resistive, inductive, and capacitive loads
• Multiple protections: Over/under voltage, current, and temperature
• Supports DC ripple, surge, dropout, and ground noise simulations
• Ideal for high-current DC Conducted Immunity testing
• LCD with real-time voltage and current metrics
• Supports both balanced and unbalanced inputs

7800 Series Linear Amplifiers are high-power, high-precision AC/DC amplifiers designed for demanding industrial and research applications.

Key Features:

• Power Output: Up to 20 kW continuous, 40 kW short-term
• Voltage: Up to ±500 Vp
• Current: Up to 800 A peak
• Bandwidth: DC to 60 kHz
• Four-quadrant operation: Source and Sink
• Modes: Selectable voltage or current control
• Protection: Overload, over-temp, short-circuit, and voltage fluctuations
• Ideal for: Resistive, inductive, and capacitive loads
• Low distortion: <0.25% THD
• High accuracy: DC drift < ±400 µV

8300 Series Power Amplifiers combine the precision of linear amplifiers with the efficiency of switch-mode technology for high-performance power delivery.

Key Features:

• Output Power: 2 kW to 10 kW (up to 50 kVA surge)
• Voltage Range: 0–140 VRMS / ±200 VDC
• Current: Up to 425A continuous, 65–300 ARMS
• Bandwidth: DC to 50 kHz
• Slew Rate: Up to 60 V/µs
• Ultra-low THD: <0.2%
• Operates in AC, DC, or AC+DC modes
• Flexible configuration: gain, current limit, impedance, and more
• Ideal for reactive, resistive, and complex loads

AE Techron 7000G Series – Low-Noise Gradient Amplifiers for MRI Imaging

Key Features:

• Robust, DC-enabled linear amplifiers with integrated power supply
• Very-low-noise linear topology for enhanced MRI image quality
• Wide bandwidth up to 1 MHz for precision applications
• Operates as voltage or current source
• No ripple noise, eliminating the need for console synchronization
• Models available for single-phase or three-phase power
• Ideal for low-field and ultra-low-field MRI research

AE Techron 8700 Series High-Frequency Power Amplifier

Key Features:

• Power output from 4 kW to 24 kW (up to 120 kVA)
• Voltage range up to ±400 Vp / 350 VDC
• Current output up to 360 ARMS continuous
• Wide bandwidth: DC to 250 kHz
• High slew rate: up to 300 V/µs
• Switch-mode efficiency with linear performance
• Scalable for both bench and rack applications
• Drives reactive and resistive loads with no power loss
• THD less than 0.8% with ultra-low noise floor
• Ideal for EMC, MIL-PRF, ISO 61000, and automotive testing

AE Techron 9100 Series High-Current Power Amplifiers

Key Features:

• Power output up to 5 kW continuous (4.2 kW for 9105 model)
• Wide bandwidth: DC to 250 kHz
• Voltage output up to 200 Vp
• Current output from 50A to 150A peak
• Fast 7 µs rise/fall time for surges and dropouts
• Slew rate up to 150 V/µs
• Four-quadrant operation (source and sink)
• Stable with highly capacitive loads
• Works from single-phase AC mains (100–250 VAC)
• Ideal for automotive, aviation, and EMC conducted immunity testing

AE Techron RLY Amplifiers – Precision Power for Relay Testing

Key Features:

• Designed for rigorous power utility industry testing
• Peak currents up to 200 amperes for challenging applications
• Wide bandwidth: DC–10 kHz (current) and DC–100 kHz (voltage)
• Low distortion and minimal phase error for accurate results
• Suitable for power grid modeling and relay verification
• Four-quadrant operation for enhanced versatility
• Multiple models for varied voltage and current requirements

Aetec 7794 High Current Industrial Amplifier

Key Features:

• Up to 200 Ap / 100 Vp; DC to 150 kHz bandwidth
• Stable with resistive, inductive, or capacitive loads
• Controlled-voltage or controlled-current operation
• Switchable rail supply for optimized load impedance
• 60A continuous output at 13.8V DC
• ±95V DC and >35 V/µs slew rate
• Four-quadrant operation: sourcing and sinking
• Extensive protection against overvoltage, overcurrent, overtemperature
• Rack-mountable chassis with LCD fault diagnostics

AETechron 7796 Amplifier – High-Current, Low-Impedance Industrial Power
Ideal for precision testing, EMC simulations, and MRI systems.

Key Features:

• Delivers over 200 Ap peak current, up to ±180V
• DC to 100 kHz bandwidth for versatile signal reproduction
• Four-quadrant operation (source/sink modes)
• Operates in both voltage and current-controlled modes
• Handles in-rush currents up to 200A
• Field-configurable rail supply modes for load optimization
• Advanced protection against voltage, current, and thermal faults
• Stackable for higher voltage or current (up to 800 Ap)

AIM-TTi 1908 Series – 5.5 Digit Dual Display Multimeter
High-performance, bench-top or portable multimeter for professional-grade precision and versatility.

Key Features:

• 5.5-digit resolution with dual display
• True RMS AC + frequency, capacitance & temperature measurements
• Dual measurement capability for parallel data monitoring
• USB standard (1908); USB, RS232, LAN/LXI on 1908P
• Optional GPIB interface (1908P)
• Powered by AC mains or internal rechargeable batteries
• High accuracy up to 0.02%, resolution down to 1µV and 0.1µA
• Ideal for both laboratory and field applications
• PC-Link software included for remote control and data logging

A precision AC power supply designed for EMC testing, pre-compliance setups, and product development labs.

Key Features:

• 1000W power output at 230V
• Low harmonic distortion for clean AC testing
• Delivers up to 4.4A RMS and 10A peak currents
• EN61000–3–2 compliant for harmonic emissions
• Available with UK, Schuko, or USA sockets
• Comprehensive built-in overload protection
• Simple connection via standard power connectors

Reliable, flexible, and programmable power delivery for bench, system, and ATE applications.

Key Features:

• PowerFlex technology for variable V/A within power limits
• Up to 60V and 20A, 180W or 420W per output
• Dual or single isolated outputs
• CV or CC operation with settings lock (S-Lock)
• Selectable OVP trips and remote sense terminals
• RS232, USB, LAN/LXI standard on P models
• GPIB available as option (P models only)
• Compact, rugged 3U quarter or half rack design
• Analog remote control (CPX400SA model)

The CIS-25 Test Kit by AE Techron is an all-in-one solution for aviation conducted and induced susceptibility testing. Designed to meet rigorous standards like DO-160 Sections 16, 18, and 19, this kit includes everything needed to perform accurate, repeatable EMC tests with minimal setup.

Key Features:

• Meets Multiple Standards: DO-160 Sections 16 (up to 24VDC), 18, 19, MIL STD 461, Airbus ABD0100.1.8
• Complete Test Kit: Includes DSR 100-25 power system, three coupling transformers, and chattering relay
• 4x Power Surge Capability: Ideal for in-rush testing (up to 200 ms)
• Built-In Standards Library: 3110A library for additional EMC tests
• Expert Guidance Included: Two hours of consulting from EMC specialist Patrick G. Andre
• Secure & Durable: Comes with a lockable storage cabinet and all necessary accessories