Products

• Current measurement from insulated probing of conductor
• Suitable for observation and measurement of current in PCB tracks, component leads and ground planes
• Wide dynamic range of 10mA to 20A peak to peak
• Wide bandwidth of DC to 5MHz
• Low noise figure equivalent to <6mA rms at full B/W
• Safety rated to 300V Cat II (600V Cat 1)
• Suitable for connection to any oscilloscope
• High accuracy general purpose H-field probe
• Converts to ‘closed magnetic circuit’ current probe

Single-phase, 2U, industrial amplifier/battery simulator

• Bench-sized
• Powered from 120V/230VAC
• Source and Sink (4 quadrant)
• Rugged Design
• 3-Year, No-Fault Warranty

Key Performance Capabilities:

• Drop outs and surges as fast as 1.2µs
• Small signal response up to 1 MHz
• 13.5 VDC at up to 28A
• Field-selectable ±40V, 75V or 150V potential

The First Wide-Bandwidth, High-Power Digital Amplifiers

• Max Continuous Output Current: 300A RMS
• Surge Rating: 2X power at up to 400 V_P or 750A
• Apparent Power Rating: Up to 5X continuous power rating atup to 400 V_P or 750A
• Supply Voltage: Three-phase, 208V ±10%, 60A, 50/60 Hz; 400V ±10%, 15A version available.
• Dimensions (HxWxD): 36.5 x 21.0 x 30.75 inches (92.7 x 53.3 x 78.1 cm)
• Weight: Appx. 540 lbs. (244.9 kg)

The new G5.RSS series features

• High control dynamics
• An exceptional accuracy
• A nominal output voltage of up to 3000 VDC
• A wide current-voltage range with an auto-ranging factor of 3.
• You get the best value for your investment.

Key Performance Capabilities:

• Slew rates up to 60 V/µsec.
• Up to 240A DC at +50VDC or –50VDC (4301-240 configuration).
• Can provide pulses of up to 800 amps at voltages of up to ±100V (4301-240 configuration).
• Adjustable compensation allows the system to maintain a 50V/2 µsec rise-time over a wide range of current outputs.

Key Performance Capabilities:

• Bandwidth: DC to 50 kHz
• Voltage: 0 to 250 V_RMS; 0 to 350 VDC
• Current: 100 to 500 A_RMS
• Distortion: 0.1%
• Power: 4 kW to 20 kW*Power levels up to 5X rated power when driving reactive loads
• High power efficiency and density

*Models available with output from 4 kW to 20 kW (capable of up to 125 kVA).

Key Performance Capabilities:

• 4-Quadrant – Can source and sink current
• ±80V – DC supply for 12V to 48V systems; meets 80V surge requirements
• 300 kHz Sine – DC ripple tests for all major standards
• 3µs Rise Time – Exceeds surge and dropout slew rate requirements
• 3mΩ DC Source Impedance – Out-performs ISO 7637-2 requirements
• Supports ground reference and supply offset testing required for ISO 16750-2 Sect. 4.8 and other similar standards

Key Performance Capabilities:

• Up to 900 watts RMS power output (7136 model)
• Small signal response up to 400 kHz
• User-adjustable precision DC offset
• User-adjustable current limit: 1A to 25A
• 4-quadrant operation
• AC/DC coupled

Key Performance Capabilities:

• Up to 900 watts RMS power output (7136 model)
• Small signal response up to 400 kHz
• User-adjustable precision DC offset
• User-adjustable current limit: 1A to 25A
• 4-quadrant operation
• AC/DC coupled

High‐Resolution Portable TDR with Frequency‐Domain Analysis Tools

Ideal for testing all types of microwave/RF and digital cables and connectors

• Rugged portable TDR with S‐parameter tools
• Resolves connector detail (<1 cm)
• 75 μm (0.003 in.) cursor resolution
• 16‐bit digital sampling at up to 250 KSPS
• Stores thousands of TDR traces
• USB host/client, 10/100 Ethernet
• Lightweight, bright color screen
• Internet streaming and remote control

Simplify Aging Aircraft Wiring Maintenance Using High-Resolution MOHR CT100 Series TDR Cable Analyzers

• Designed for use with the high-resolution CT100 TDR Cable Tester
• Ideal for TDR testing MIL-STD-1553B data bus aerospace cable assemblies
• Detect and localize open, short, and partial cable and connector faults on the main bus and stubs
• Detects cable and connector faults through 3+ transformer couplers
• Simplifies troubleshooting of aging aircraft MIL-STD-1553 cable assemblies

• compact and completely modular design
• high effectiveness in all operation modes, few requirements on building infrastructure
• ability to use an existing liquid cooling system directly
• optional matched liquid-to-air cooling unit TC.LAE available
• possibility of upgrading to systems of up to 1 MVA
• high level of system dynamics, ≤ 5 kHz modulation bandwidth
• non-restrictive capability of refeeding in the Q4 operation mode
• possibility of operating as an autonomous 4-Q and 3-phase quasi-analogue amplifier
• possibility of “Hardware-in-the loop”-operation (HIL mode)
• user friendly application software with pre-configured test patterns
• possibility of integrating into a complete SAS simulation and test system
• galvanic isolation available as an option without derating the simulator port data

Bidirectional (source & sink), Regenerative 0…65VDC to 0…1500VDC, 20kW up to 1.5 MW 

• cell system nominal voltage and type of chemistry
• number of cells
• internal resistance and associated parameters
• cell temperature progression
• allowed current
• charge efficiency
• energy computing and management facilities
• time-dependent and functional dependent parameters

• Setting of operational parameters for each output phase: (frequency, phase, voltage, basic waveform)
• Defining functional blocks enabling a wide variety of modulation capabilities
• Defining, editing and storing of even complex and long test sequences
• Preview window for output voltage waveforms
• LC load mode, definition of complex equivalent circuits
• Hand drawing curve tool and FOURIER tool (harmonics synthesis)
• TC.ACS provides an extensive safety concept in order to detect unwanted or off-limit conditions very quickly and to initiate controlled limiting or even a shutdown.

• compact and completely modular design
• high effectiveness in all operation modes, few requirements on building infrastructure
• ability to use an existing liquid cooling system directly
• optional matched liquid-to-air cooling unit TC.LAE available
• possibility of upgrading to systems of up to 1 MVA
• high level of system dynamics, ≤ 5 kHz modulation bandwidth
• non-restrictive capability of refeeding in the Q4 operation mode
• possibility of operating as an autonomous 4-Q and 3-phase quasi-analogue amplifier
• possibility of “Hardware-in-the loop”-operation (HIL mode)
• user friendly application software with pre-configured test patterns
• possibility of integrating into a complete SAS simulation and test system
• galvanic isolation available as an option without derating the simulator port data

• 16K Video Generator & Analyzer
• Dolby Vision™, HDR 10 and HDR 10+
• validating DP 1.4a & DP 2.0 Link Layer on DP Sinks and Sources
• Power Input +12 Vdc (AC/DC converter included)
• Module Size/Weight TBD for Weight and Size