Products

The 3110A Standards Waveform Generator is a feature-rich, intuitive tool for engineers conducting EMC testing. From automotive to aviation applications, this unit simplifies the most complex test routines.

Key Features:

• 3,400+ Built-In Tests for automotive and industry standards
• Fast Rise Time: 3 µs full-scale with up to 1 MHz bandwidth
• Segment-Based Waveform Creation for custom sequences
• Free Lifetime Standards Updates
• Automated Triggering via GPIO or LAN
• Flexible Output Control including frequency, amplitude, and DC offset
• Extremely Precise Resolution: 0.01 Hz frequency, 76 µV amplitude
• Supports All Common Waveforms: Sine, square, triangle, DC, ripple, and more

The 7224 Linear Amplifier delivers power, speed, and precision in a compact 2U form factor. Designed for lab, test, and simulation environments, it provides outstanding performance for demanding applications.

Key Features:

• Up to 900W RMS output power
• Operates in controlled-current or controlled-voltage mode
• Field-configurable for low or high impedance loads
• DC to 1 MHz small signal bandwidth
• Produces up to 50A current or 158V peak
• Slew rate of 90 V/μs for sharp waveform reproduction
• Over-voltage, over-current, and over-temp protection circuits
• Compact 2U rack-mount or benchtop design
• Suitable for Helmholtz coil drivers, MRI/NMR, SMPS component testing

The 7548 Linear Amplifier is a high-output, low-noise solution engineered for precision and reliability in demanding environments.

Key Features:

• Up to 100 Ap / 195 Vp output
• Delivers 12,000W peak power for 40 ms
• Supports continuous 5,500W output into 1Ω load
• Operates from DC to 100 kHz bandwidth
• Field-selectable current or voltage mode
• Ideal for MIL-STD-704F three-phase testing
• Stackable for 800 Vp or 170 Ap system output
• Built-in protection against over-voltage, over-temp, and overload
• Intuitive LCD display and status indicators

7796HC Linear Power Amplifier – High Current DC & AC Precision

Key Features:

• Output up to 85A continuous, 200A in-rush current
• Frequency response: DC to 100+ kHz
• Four-quadrant operation: source and sink
• Field-selectable voltage or current modes
• Stable with resistive, inductive, and capacitive loads
• Multiple protections: Over/under voltage, current, and temperature
• Supports DC ripple, surge, dropout, and ground noise simulations
• Ideal for high-current DC Conducted Immunity testing
• LCD with real-time voltage and current metrics
• Supports both balanced and unbalanced inputs

7800 Series Linear Amplifiers are high-power, high-precision AC/DC amplifiers designed for demanding industrial and research applications.

Key Features:

• Power Output: Up to 20 kW continuous, 40 kW short-term
• Voltage: Up to ±500 Vp
• Current: Up to 800 A peak
• Bandwidth: DC to 60 kHz
• Four-quadrant operation: Source and Sink
• Modes: Selectable voltage or current control
• Protection: Overload, over-temp, short-circuit, and voltage fluctuations
• Ideal for: Resistive, inductive, and capacitive loads
• Low distortion: <0.25% THD
• High accuracy: DC drift < ±400 µV

8300 Series Power Amplifiers combine the precision of linear amplifiers with the efficiency of switch-mode technology for high-performance power delivery.

Key Features:

• Output Power: 2 kW to 10 kW (up to 50 kVA surge)
• Voltage Range: 0–140 VRMS / ±200 VDC
• Current: Up to 425A continuous, 65–300 ARMS
• Bandwidth: DC to 50 kHz
• Slew Rate: Up to 60 V/µs
• Ultra-low THD: <0.2%
• Operates in AC, DC, or AC+DC modes
• Flexible configuration: gain, current limit, impedance, and more
• Ideal for reactive, resistive, and complex loads

AE Techron 8700 Series High-Frequency Power Amplifier

Key Features:

• Power output from 4 kW to 24 kW (up to 120 kVA)
• Voltage range up to ±400 Vp / 350 VDC
• Current output up to 360 ARMS continuous
• Wide bandwidth: DC to 250 kHz
• High slew rate: up to 300 V/µs
• Switch-mode efficiency with linear performance
• Scalable for both bench and rack applications
• Drives reactive and resistive loads with no power loss
• THD less than 0.8% with ultra-low noise floor
• Ideal for EMC, MIL-PRF, ISO 61000, and automotive testing

AE Techron 9100 Series High-Current Power Amplifiers

Key Features:

• Power output up to 5 kW continuous (4.2 kW for 9105 model)
• Wide bandwidth: DC to 250 kHz
• Voltage output up to 200 Vp
• Current output from 50A to 150A peak
• Fast 7 µs rise/fall time for surges and dropouts
• Slew rate up to 150 V/µs
• Four-quadrant operation (source and sink)
• Stable with highly capacitive loads
• Works from single-phase AC mains (100–250 VAC)
• Ideal for automotive, aviation, and EMC conducted immunity testing

AE Techron RLY Amplifiers – Precision Power for Relay Testing

Key Features:

• Designed for rigorous power utility industry testing
• Peak currents up to 200 amperes for challenging applications
• Wide bandwidth: DC–10 kHz (current) and DC–100 kHz (voltage)
• Low distortion and minimal phase error for accurate results
• Suitable for power grid modeling and relay verification
• Four-quadrant operation for enhanced versatility
• Multiple models for varied voltage and current requirements

Aetec 7794 High Current Industrial Amplifier

Key Features:

• Up to 200 Ap / 100 Vp; DC to 150 kHz bandwidth
• Stable with resistive, inductive, or capacitive loads
• Controlled-voltage or controlled-current operation
• Switchable rail supply for optimized load impedance
• 60A continuous output at 13.8V DC
• ±95V DC and >35 V/µs slew rate
• Four-quadrant operation: sourcing and sinking
• Extensive protection against overvoltage, overcurrent, overtemperature
• Rack-mountable chassis with LCD fault diagnostics

AETechron 7796 Amplifier – High-Current, Low-Impedance Industrial Power
Ideal for precision testing, EMC simulations, and MRI systems.

Key Features:

• Delivers over 200 Ap peak current, up to ±180V
• DC to 100 kHz bandwidth for versatile signal reproduction
• Four-quadrant operation (source/sink modes)
• Operates in both voltage and current-controlled modes
• Handles in-rush currents up to 200A
• Field-configurable rail supply modes for load optimization
• Advanced protection against voltage, current, and thermal faults
• Stackable for higher voltage or current (up to 800 Ap)

AIM-TTi 1908 Series – 5.5 Digit Dual Display Multimeter
High-performance, bench-top or portable multimeter for professional-grade precision and versatility.

Key Features:

• 5.5-digit resolution with dual display
• True RMS AC + frequency, capacitance & temperature measurements
• Dual measurement capability for parallel data monitoring
• USB standard (1908); USB, RS232, LAN/LXI on 1908P
• Optional GPIB interface (1908P)
• Powered by AC mains or internal rechargeable batteries
• High accuracy up to 0.02%, resolution down to 1µV and 0.1µA
• Ideal for both laboratory and field applications
• PC-Link software included for remote control and data logging

A precision AC power supply designed for EMC testing, pre-compliance setups, and product development labs.

Key Features:

• 1000W power output at 230V
• Low harmonic distortion for clean AC testing
• Delivers up to 4.4A RMS and 10A peak currents
• EN61000–3–2 compliant for harmonic emissions
• Available with UK, Schuko, or USA sockets
• Comprehensive built-in overload protection
• Simple connection via standard power connectors

Reliable, flexible, and programmable power delivery for bench, system, and ATE applications.

Key Features:

• PowerFlex technology for variable V/A within power limits
• Up to 60V and 20A, 180W or 420W per output
• Dual or single isolated outputs
• CV or CC operation with settings lock (S-Lock)
• Selectable OVP trips and remote sense terminals
• RS232, USB, LAN/LXI standard on P models
• GPIB available as option (P models only)
• Compact, rugged 3U quarter or half rack design
• Analog remote control (CPX400SA model)

The BAT EMC software suite by NEXIO is an advanced electromagnetic compatibility testing platform designed to automate, control, and streamline EMC testing workflows. Built for laboratories, automotive engineers, and compliance specialists, it enables accurate emission and immunity testing with powerful configuration and reporting tools.

Key Features

• Automated EMC emission and immunity testing workflows
• Supports conducted and radiated emission and immunity tests
• Configurable test parameters including RBW, detectors, scan time, and limits
• Automotive-focused testing aligned with CISPR25 standards
• BAT-ELEC module for transient, burst, and surge testing automation
• Real time monitoring tools including voltmeters, analyzers, and cameras
• Centralized project management for EMC test data and resources
• Multi brand compatibility for test generators and measurement equipment
• Automatic compliance report generation for regulatory requirements
• Designed for aerospace, automotive, healthcare, and industrial labs

The BAT metrology software suite by NEXIO is a precision-driven measurement solution designed to support EMC laboratories and engineering teams in analyzing, calibrating, and validating electrical and RF test systems. It enhances accuracy, ensures compliance, and simplifies complex measurement workflows across multiple testing environments.

Key Features

• Comprehensive metrology platform for EMC and RF measurement systems
• Supports VNA based testing for RSIL, RCD, and cable validation
• Oscilloscope based analysis for ESD guns and signal generators
• Amplifier calibration to maintain consistent performance standards
• BAT-NSA and SVSWR testing for anechoic chamber and OATS environments
• Ensures accurate signal measurement and system validation
• Improves compliance, reliability, and measurement consistency
• Suitable for EMC laboratories, research centers, and industrial testing
• Reduces calibration errors and improves test repeatability
• Supports modern metrology workflows for complex RF systems