Products

The measurement system for all emission measurments in the frequency range 1 Hz – 44 GHz.

• Full compliance EMI Reciever according to standard CISPR 16-1· 1, ANSI C63.2, MIL->461, and DO·160
• Spectrum Analyzer
• Integrated LOW Noise Ampllfier (lNAI)
• Integrated Preselect1on
• Tradttional and FFT·based Mode
• Automatic Stepped Attenuator
• Ultra Low Noise Floor
• Excellent spurious Performance
• Real-time Spectrum Analyzer optional
• Vast IQ-Bandwidth

TDEMI Mobile+. The ultra mobile EMI receiver – Emission measurements everytime, everywhere. Fully stand-alone operable.

• Frequency Ranges 10Hz – 1GHz, 3GHz, 6GHz or 7GHz
• 16000x faster than conventional receivers
• Super compact design and 12V supply
• 225 MHz fully gapless real-time analysis bandwidth
• Weighted Real-time Spectrogram

Ultra High Performance RT Spectrum Analyzer. Ultrafast EMI Measurements.

• Frequency Range from 1 Hz up to 50 GHz
• 225 MHz Real-time analysis bandwidth
• 100 dB Dynamic Range
• Ultrahigh performance preselection in all modes
• Up to 510 MHz Real-time IQ-Analysis bandwidth
• Ultra High Performance Spectrum Analyzer

Unleash the power of modern, versatile, and sophisticated AC sources with our LSX Series – Programmable AC Power Source. These powerhouses come in single and three-phase options, ranging from 1.5kVA to 6kVA. Equipped with an advanced programmable controller featuring a vivid colour touchscreen interface, the LSX Series is not just cost-effective but also fully programmable for basic frequency conversion, advanced AC power line disturbance tests, and ATE applications.

Key Features Provide Application Versatility

• USB, LAN (LXI), IEEE-488.2 and RS-232C with SCPI compatibility
• Compatible with PPSC Studio graphical user interface
• LabVIEW for Windows®/LabWindows® drivers
• Waveform Creation by Harmonic Synthesis
• Waveform Capture (Voltage and Current)
• Harmonic Analysis (Voltage and Current)
• Metering of RMS and Peak Values
• Continuous Self Calibration (CSC)
• Line Sync
• 6:1 Peak Current Capability
• Low Impedance for EN61000-3-2, 3 Testing
• Programmable Output Impedance
• Up to 0-300 VAC Direct Coupled Out
• 1 Phase / 3 Phase Switch Selectable
• 15-5000 Hz Full Power Bandwidth
• Power Levels from 500 VA to 6 kVA standard; 30kVA optional
• Externally Referenced Meter Calibration
• CE Safety & EMC and NTRL Safety Mark

The AZX Series (Regenerative AC / DC Power Source) is a family of high power, single, split and three phase, AC, DC and AC+DC output capable Power Sources with full energy recovery to the AC mains when sinking power from the equipment under test. Available models range from 30 kVA to 440 kVA. Using a modern color touch screen based user interface for ease of use, the AZX Series is cost effective and fully programmable for both basic frequency conversion and advanced AC power line or DC power disturbance test applications requiring up to 1000 Hz fundamental frequency.

The energy recovery capability allows both sourcing and sinking of current and power up to 100% of rated power. Adding the Load Option (Option L) adds full electronic regenerative AC & DC Load programming capability to the AZX.

The new G5.RSS series features

• High control dynamics
• An exceptional accuracy
• A nominal output voltage of up to 3000 VDC
• A wide current-voltage range with an auto-ranging factor of 3.
• You get the best value for your investment.

Key Performance Capabilities:

• Slew rates up to 60 V/µsec.
• Up to 240A DC at +50VDC or –50VDC (4301-240 configuration).
• Can provide pulses of up to 800 amps at voltages of up to ±100V (4301-240 configuration).
• Adjustable compensation allows the system to maintain a 50V/2 µsec rise-time over a wide range of current outputs.

Key Performance Capabilities:

• Bandwidth: DC to 50 kHz
• Voltage: 0 to 250 V_RMS; 0 to 350 VDC
• Current: 100 to 500 A_RMS
• Distortion: 0.1%
• Power: 4 kW to 20 kW*Power levels up to 5X rated power when driving reactive loads
• High power efficiency and density

*Models available with output from 4 kW to 20 kW (capable of up to 125 kVA).

Key Performance Capabilities:

• 4-Quadrant – Can source and sink current
• ±80V – DC supply for 12V to 48V systems; meets 80V surge requirements
• 300 kHz Sine – DC ripple tests for all major standards
• 3µs Rise Time – Exceeds surge and dropout slew rate requirements
• 3mΩ DC Source Impedance – Out-performs ISO 7637-2 requirements
• Supports ground reference and supply offset testing required for ISO 16750-2 Sect. 4.8 and other similar standards

Key Performance Capabilities:

• Up to 900 watts RMS power output (7136 model)
• Small signal response up to 400 kHz
• User-adjustable precision DC offset
• User-adjustable current limit: 1A to 25A
• 4-quadrant operation
• AC/DC coupled

Key Performance Capabilities:

• Up to 900 watts RMS power output (7136 model)
• Small signal response up to 400 kHz
• User-adjustable precision DC offset
• User-adjustable current limit: 1A to 25A
• 4-quadrant operation
• AC/DC coupled

• Frequency Range 10 Hz – 1GHz, 3GHz or 6GHz
• 4000x faster in your pre-certifcation work
• compact design and +12V power supply
• 162.5 MHz full gapless real-time analysis bandwidth
• Weighted Real-time Spectrogram

• requency Range from DC up to 40 GHz
• 685 MHz Real-time analysis bandwidth
• Dynamic range of more than 100 dB
• Multi-GHz real-time scanning up to 40 GHz
• all 6dB RBWs acc. to CISPR, MIL, DO, ANSI, FCC
• fastest super-heterodyn receiver on the planet

• compact and completely modular design
• high effectiveness in all operation modes, few requirements on building infrastructure
• ability to use an existing liquid cooling system directly
• optional matched liquid-to-air cooling unit TC.LAE available
• possibility of upgrading to systems of up to 1 MVA
• high level of system dynamics, ≤ 5 kHz modulation bandwidth
• non-restrictive capability of refeeding in the Q4 operation mode
• possibility of operating as an autonomous 4-Q and 3-phase quasi-analogue amplifier
• possibility of “Hardware-in-the loop”-operation (HIL mode)
• user friendly application software with pre-configured test patterns
• possibility of integrating into a complete SAS simulation and test system
• galvanic isolation available as an option without derating the simulator port data

Bidirectional (source & sink), Regenerative 0…65VDC to 0…1500VDC, 20kW up to 1.5 MW 

• cell system nominal voltage and type of chemistry
• number of cells
• internal resistance and associated parameters
• cell temperature progression
• allowed current
• charge efficiency
• energy computing and management facilities
• time-dependent and functional dependent parameters