1 800 665 7301 | info@tmetrix.com

  • The 3110A Standards Waveform Generator is a feature-rich, intuitive tool for engineers conducting EMC testing. From automotive to aviation applications, this unit simplifies the most complex test routines.

    Key Features:

    • 3,400+ Built-In Tests for automotive and industry standards
    • Fast Rise Time: 3 µs full-scale with up to 1 MHz bandwidth
    • Segment-Based Waveform Creation for custom sequences
    • Free Lifetime Standards Updates
    • Automated Triggering via GPIO or LAN
    • Flexible Output Control including frequency, amplitude, and DC offset
    • Extremely Precise Resolution: 0.01 Hz frequency, 76 µV amplitude
    • Supports All Common Waveforms: Sine, square, triangle, DC, ripple, and more

     

  • The 7224 Linear Amplifier delivers power, speed, and precision in a compact 2U form factor. Designed for lab, test, and simulation environments, it provides outstanding performance for demanding applications.

    Key Features:

    • Up to 900W RMS output power
    • Operates in controlled-current or controlled-voltage mode
    • Field-configurable for low or high impedance loads
    • DC to 1 MHz small signal bandwidth
    • Produces up to 50A current or 158V peak
    • Slew rate of 90 V/μs for sharp waveform reproduction
    • Over-voltage, over-current, and over-temp protection circuits
    • Compact 2U rack-mount or benchtop design
    • Suitable for Helmholtz coil drivers, MRI/NMR, SMPS component testing

     

  • The 7548 Linear Amplifier is a high-output, low-noise solution engineered for precision and reliability in demanding environments.

    Key Features:

    • Up to 100 Ap / 195 Vp output
    • Delivers 12,000W peak power for 40 ms
    • Supports continuous 5,500W output into 1Ω load
    • Operates from DC to 100 kHz bandwidth
    • Field-selectable current or voltage mode
    • Ideal for MIL-STD-704F three-phase testing
    • Stackable for 800 Vp or 170 Ap system output
    • Built-in protection against over-voltage, over-temp, and overload
    • Intuitive LCD display and status indicators

     

  • 7796HC Linear Power Amplifier – High Current DC & AC Precision

    Key Features:

    • Output up to 85A continuous, 200A in-rush current
    • Frequency response: DC to 100+ kHz
    • Four-quadrant operation: source and sink
    • Field-selectable voltage or current modes
    • Stable with resistive, inductive, and capacitive loads
    • Multiple protections: Over/under voltage, current, and temperature
    • Supports DC ripple, surge, dropout, and ground noise simulations
    • Ideal for high-current DC Conducted Immunity testing
    • LCD with real-time voltage and current metrics
    • Supports both balanced and unbalanced inputs

     

  • 7800 Series Linear Amplifiers are high-power, high-precision AC/DC amplifiers designed for demanding industrial and research applications.

    Key Features:

    • Power Output: Up to 20 kW continuous, 40 kW short-term
    • Voltage: Up to ±500 Vp
    • Current: Up to 800 A peak
    • Bandwidth: DC to 60 kHz
    • Four-quadrant operation: Source and Sink
    • Modes: Selectable voltage or current control
    • Protection: Overload, over-temp, short-circuit, and voltage fluctuations
    • Ideal for: Resistive, inductive, and capacitive loads
    • Low distortion: <0.25% THD
    • High accuracy: DC drift < ±400 µV

     

  • 8300 Series Power Amplifiers combine the precision of linear amplifiers with the efficiency of switch-mode technology for high-performance power delivery.

    Key Features:

    • Output Power: 2 kW to 10 kW (up to 50 kVA surge)
    • Voltage Range: 0–140 VRMS / ±200 VDC
    • Current: Up to 425A continuous, 65–300 ARMS
    • Bandwidth: DC to 50 kHz
    • Slew Rate: Up to 60 V/µs
    • Ultra-low THD: <0.2%
    • Operates in AC, DC, or AC+DC modes
    • Flexible configuration: gain, current limit, impedance, and more
    • Ideal for reactive, resistive, and complex loads

     

  • AE Techron 7000G Series – Low-Noise Gradient Amplifiers for MRI Imaging

    Key Features:

    • Robust, DC-enabled linear amplifiers with integrated power supply
    • Very-low-noise linear topology for enhanced MRI image quality
    • Wide bandwidth up to 1 MHz for precision applications
    • Operates as voltage or current source
    • No ripple noise, eliminating the need for console synchronization
    • Models available for single-phase or three-phase power
    • Ideal for low-field and ultra-low-field MRI research

     

  • AE Techron 8700 Series High-Frequency Power Amplifier

    Key Features:

    • Power output from 4 kW to 24 kW (up to 120 kVA)
    • Voltage range up to ±400 Vp / 350 VDC
    • Current output up to 360 ARMS continuous
    • Wide bandwidth: DC to 250 kHz
    • High slew rate: up to 300 V/µs
    • Switch-mode efficiency with linear performance
    • Scalable for both bench and rack applications
    • Drives reactive and resistive loads with no power loss
    • THD less than 0.8% with ultra-low noise floor
    • Ideal for EMC, MIL-PRF, ISO 61000, and automotive testing

     

  • AE Techron 9100 Series High-Current Power Amplifiers

    Key Features:

    • Power output up to 5 kW continuous (4.2 kW for 9105 model)
    • Wide bandwidth: DC to 250 kHz
    • Voltage output up to 200 Vp
    • Current output from 50A to 150A peak
    • Fast 7 µs rise/fall time for surges and dropouts
    • Slew rate up to 150 V/µs
    • Four-quadrant operation (source and sink)
    • Stable with highly capacitive loads
    • Works from single-phase AC mains (100–250 VAC)
    • Ideal for automotive, aviation, and EMC conducted immunity testing

     

  • AE Techron RLY Amplifiers – Precision Power for Relay Testing

    Key Features:

    • Designed for rigorous power utility industry testing
    • Peak currents up to 200 amperes for challenging applications
    • Wide bandwidth: DC–10 kHz (current) and DC–100 kHz (voltage)
    • Low distortion and minimal phase error for accurate results
    • Suitable for power grid modeling and relay verification
    • Four-quadrant operation for enhanced versatility
    • Multiple models for varied voltage and current requirements

     

  • Aetec 7794 High Current Industrial Amplifier

    Key Features:

    • Up to 200 Ap / 100 Vp; DC to 150 kHz bandwidth
    • Stable with resistive, inductive, or capacitive loads
    • Controlled-voltage or controlled-current operation
    • Switchable rail supply for optimized load impedance
    • 60A continuous output at 13.8V DC
    • ±95V DC and >35 V/µs slew rate
    • Four-quadrant operation: sourcing and sinking
    • Extensive protection against overvoltage, overcurrent, overtemperature
    • Rack-mountable chassis with LCD fault diagnostics

     

  • AETechron 7796 Amplifier – High-Current, Low-Impedance Industrial Power
    Ideal for precision testing, EMC simulations, and MRI systems.

    Key Features:

    • Delivers over 200 Ap peak current, up to ±180V
    • DC to 100 kHz bandwidth for versatile signal reproduction
    • Four-quadrant operation (source/sink modes)
    • Operates in both voltage and current-controlled modes
    • Handles in-rush currents up to 200A
    • Field-configurable rail supply modes for load optimization
    • Advanced protection against voltage, current, and thermal faults
    • Stackable for higher voltage or current (up to 800 Ap)

     

  • The CIS-25 Test Kit by AE Techron is an all-in-one solution for aviation conducted and induced susceptibility testing. Designed to meet rigorous standards like DO-160 Sections 16, 18, and 19, this kit includes everything needed to perform accurate, repeatable EMC tests with minimal setup.

    Key Features:

    • Meets Multiple Standards: DO-160 Sections 16 (up to 24VDC), 18, 19, MIL STD 461, Airbus ABD0100.1.8
    • Complete Test Kit: Includes DSR 100-25 power system, three coupling transformers, and chattering relay
    • 4x Power Surge Capability: Ideal for in-rush testing (up to 200 ms)
    • Built-In Standards Library: 3110A library for additional EMC tests
    • Expert Guidance Included: Two hours of consulting from EMC specialist Patrick G. Andre
    • Secure & Durable: Comes with a lockable storage cabinet and all necessary accessories

  • The DSR 400 Series Test System is a compact, high-performance simulator for rigorous AC and DC immunity testing. Built for DO 160 and MIL STD 704 compliance, it integrates a powerful waveform generator, cutting-edge power technology, and a vast standards library—making it an ideal solution for demanding EMC test labs.

    Key Features:

    • Complete Test Solution for DO 160 Sec. 16 and MIL STD 704
    • Built-In Standards Library with 3,400+ automotive and aviation test routines
    • 4-Quadrant Operation: Sources and sinks current for complex test needs
    • High Surge Capability: Delivers 5x rated power for 200 ms
    • Fast Rise Time: Less than 30 µs for real-time performance
    • Modular Output: 80A or 160A continuous current options available
    • Multiple Waveform Options: Includes sine, ripple, triangle, sawtooth, square, and DC
    • Remote Control Ready: LAN and GPIO integration for larger systems
    • Easy-to-Use Interface: Pre-configured or user-custom test sequences

     

  • Featuring an ultra-compact 0.35”microLED display with high-brightnessand high-resolution technology,delivering dynamic visuals and seamlessintegration for next-generationautomotive heads-up display (HUD).

    Key Features of High Brightness High Resolution 0.35″ Micro-Display:

    • OVERVIEWUltra-High Brightness: Engineered to perform in a widerange of lighting conditions, ensuring excellent visibility inboth indoor and outdoor environments.
    • Robust Durability: Built to withstand demandingconditions for long-term reliability.
    • Ultra-Thin & Lightweight: Designed for seamlessintegration into compact spaces, leveraging microLED’sinherently slim profile without compromisingperformance.
    • Power-Efficient Design: Consumes significantly less powercompared to traditional display technologies, extendingbattery life for wearable devices.

     

  • Engineered for cutting-edge EV, automotive, and aerospace compliance, the HVR 1000 is a complete high-voltage ripple test system built to handle demanding lab environments with unmatched precision and safety.

    Key Features:

    • Wide Frequency Range: AC ripple from 10 Hz to 200 kHz
    • High Voltage Output: Up to 1000V DC and 60 kW power
    • Waveform Versatility: Generates sine, triangle, and custom signals
    • Robust Safety: Multi-layer overvoltage, overcurrent, and thermal protection
    • Zero Licensing Fees: Future test standard updates included
    • User-Centric Interface: Intuitive controls with HDMI and LAN support
    • Flexible Configuration: Available as HVR 1000RG (Ripple Generator only)
    • Space-Saving Design: Small footprint, ideal for compact lab setups