HIOKI E E CORPORATION

• Noise reduction technology improves noise resistance
• Screen and audio*2 guidance simplifies measurement
• Measurement data is linked to site information and saved, reducing management man-hours
• A variety of measurement data can be centrally managed using Hioki’s GENNECT Cross app*3
• New protector delivers better ergonomic hold and durability in the field.
• Instantaneously diagnose battery degradation (PASS, WARNING, FAIL) by measuring internal resistance and voltage*1
•  Battery measurement can be performed while the battery is connected to its host device, without taking it offline
• Measure and save data in as fast as 2 seconds, a 60% improvement from the legacy 3554

3-Channel AC/DC Power Meter for Single-Phase to 3P4W Equipment such as Motors, Inverters, Power Conditioners, and Power Supplies

• Voltage/current/power basic accuracy of ±0.1% *
• Direct input up to 1000 V AC/DC / 65 A
• Harmonic measurement as standard feature, IEC61000-4-7 compliant
• Little instrument loss, even with large currents. DCCT input with an input resistance of 1 mΩ or less.
• Power factor effect of ±0.1% f.s. delivers highly accurate measurements even for no-load testing of transformers with a low power factor
• Measurement of multiple connections in the optimal range for each due to independent ranges for each channel
• Measure up to 5000 A AC with optional current sensor

• Compliant with a multitude of standards
• Constant-current testing (max. 31.0 A) with feedback control
• [ SOFT START ] function
• Fluorescent tube display (VFD)
• Test data count function
• Setting value store function
• Light weight and compact dimensions

• Voltage Control from a PC
• Standards-Based Testing
• Settable Ramp Up/Down Test Voltage Timing
• Test Status Read/Write
• Pass Hold Function (0: No Hold, 1: Hold)
• Insulation Resistance Test End Mode
• “START” Interface Command
• Electrical Discharge Function
• Insulation Resistance Measurement Range
• Maximum 32-Channel Multi-Point Testing
• Simultaneous Protective Ground Continuity Testing

• Uninterrupted polarity switching function
• Safety conductor current measurement function
• Automatic measurement functionality
• 110% voltage application jack
• Circuit breaker for device under measurement
• Save measurement data for 100 devices
• Improved test reliability
• Simple, interactive operation
• Ability to store up to 30 sets of measurement conditions

High-speed 20MS/s 32-channel Fully-isolated Memory Recorder Provides Simultaneous Data Acquisition Over 32 Analog + 32 Logic Channels

• Generate and record waveforms with a single unit
• Output previously recorded problematic waveforms and apply to devices under test to simulate potential issues
• 32 analog + 32 logic channels to 28 analog + 64 logic channels
• High-speed sampling up to 20MS/s with fully isolated inputs
• Safe measurement with all isolated analog inputs
• Large capacity memory of total 512M-words
• Measure various system signals from high voltage to ultra low voltage simultaneously

• Measure the fundamental waveform component using the average rectified method
• Expanded -25 °C to 65 °C operating temperature range
• Connect the CT6280 flexible sensor to measure up to 4199 A in thick or paired wires
• Drop proof design withstands drop from a height of 1 meter

• 5-range testing voltage of 50 V/100 MΩ to 1000 V/4000 MΩ
• Stable & medium-speed digital readings, 0.8 second response time of PASS/ FAIL decisions
• Drop proof onto concrete from 1m (3.28 feet)
• Bright LED, luminous LCD, test lead with bright LED lamp to illuminate near hand (Also available in the IR4056-21)
• Continuity check via 200 mA testing
• Built in AC/DC voltage meter, useful for testing solar power generation systems and electric vehicles

• Maximum safety in the field by absolutely preventing short-circuit accidents with fused measurement terminals and current-limiting resistor
• ±0.3% DC V basic accuracy, wide 40 Hz to 1 kHz AC V frequency characteristics
• Low-pass filter (100 Hz/ 500 Hz) cuts high harmonics (when measuring inverter fundamental waveforms)
• Connect to PC with USB communication function (optional)
• Broad -25°C (-13°F) to 65°C (149°F) operating temperature range CAT IV 600 V, CAT III 1000 V

On Measurement Spots with Two-Beam Laser Marker, Ideal for HVAC Applications

• Pistol design with easy-to-see display
• A full menu of basic measuring functions
• Easily test in difficult locations, moving objects or where there is danger of electric shock

• Top “primary supply level” safety class rating for voltage detectors
• CAT IV 1000 V design meets CE Mark qualifications
• Continuously indicate battery status with green indicator lamp
• Both visual and audible voltage detection indication
• Automatic power switching prevents battery discharge

• Simply clip clamps onto wire insulation
• Green LED arrow clearly shows phase direction, perfect for visual reports
• Rotating LED indicator shows the phase sequence for a 3-phase power supply at a glance
• Intermittent beeps signal positive phase; continuous tone signals reverse phase
• Magnetic base allows the instrument to be secured on a distribution panel