Products

• Current measurement from insulated probing of conductor
• Suitable for observation and measurement of current in PCB tracks, component leads and ground planes
• Wide dynamic range of 10mA to 20A peak to peak
• Wide bandwidth of DC to 5MHz
• Low noise figure equivalent to <6mA rms at full B/W
• Safety rated to 300V Cat II (600V Cat 1)
• Suitable for connection to any oscilloscope
• High accuracy general purpose H-field probe
• Converts to ‘closed magnetic circuit’ current probe

Precision LCR Meter with Component Fixture and Limits Comparator

Vehicle Charger (12V/24V) for PSA series spectrum analyzers

Pulse and Universal Generator 50MHz, single channel

Waveform Amplifier 30 volts pk-pk

• Customizable & savable test setups
• Program & Datalog Storage
• User Defined Temperature Limits
• Local & Remote Operations
• LabView™ drivers
• IEEE-488, RS232 ports

• 20 Amp Operation: Full performance with 20 amp service
• Automatic Power Reduction: Reduces power usage during idle periods
• Heat Only Mode: Reduces power usage when cold temperatures are not used
• WhisperStream Technology: quieter, smooth-sounding operation, 56 dBA
• Frost Free Test Environment: dry air purge for tester interface, prevents condensation:
  0.5 to 3scfm (0.25 to 1.5 l/s)
• Heated Defrost: quickly removes moisture buildup from internal chiller
• DUT Temperature Control : Proprietary control algorithm enables DUT temperature to be directly controlled
• Transition Rate*
  -55 to +125°C, approx. 10 seconds
  125 to -55°C, approx. 10 seconds
• System Airflow Output*
  4 to 18scfm (1.9 to 8.5 l/s) Continuous
• Temperature Range*
  -80 to +225°C (60Hz) No LN2 or LCO2 Required

• High reliability thermal cycling without thermoelectric modules
• Temperature range: -65 to 175°C
• Cooling power:
  • 40W at -40°C for lower power devices
  • 55W at -55°C and 120W at -40°C.
• Transition rate: up to <35 sec over 25 to -40°C
• Easy and secure thermal connection to in-circuit or test socked DUT
• Touch-screen controller: user-programmable temperatures, graphing, data logging
• Communications options: Ethernet, USB, IEEE, RS232

-60° to +200°C

• Economy model with high thermal capacity
• Precise temperatures with fast transitions from -60 to 200°C
• No annual leak testing required per EU 517/2014 F-Gas Regulation
• Effective testing and conditioning of electronic components, boards, and modules
• Available for 50 and 60Hz operation
• No need for Liquid Nitrogen (LN2) or Liquid Carbon Dioxide (LCO2)
• Remote communications and set up and touch screen operation
• User Defined Temperature Limits

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +12 to -12 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510 MCOR12 Power Modules are identical and interchangeable.
• Has two high-precision measurements of output current;
  • one is used to close the regulation control loop,
  • provides an independent monitoring signal to the Crate Interface Card.
• Fault sensing circuitry in the module sets a Fault Latch which inhibits the output.
• A (momentary) Sync input signal inhibits MOSFET switching when it is active (high);
  • this eliminate switching noise .
  • reduces power line noise during sensitive analog signal measurements.

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +30 to -30 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510R30 MCOR30 Power Modules are identical and interchangeable
  • Programming Card is plugged into the replacement module.
• Each channel has a critically-damped, LC noise filter with a cut-off frequency of about 8 kHz.
• A 16-pin front panel diagnostics connector taps onto major circuit nodes which enables quick “inthe-crate” fault evaluation

• 2U Chassis – 19″ rack mount 3.48” Height, 9.60” Depth and Weight 6lb.
• Power 120V AC 60Hz
• Washable front removable air filter
• Ball Bearing AC fans provide 330 CFM
• Dual plenum design
• Cooling for 160mm,220mm depth modules
• Diverts lower warmed air to rear of Cabinet
• RM option diverts lower air to front of Cabinet

• accommodate these control schemes
• total control system interface on a single VME-standard card
• occupies the left-most slot of the crate
• monitoring voltage reference inputs, output voltages and fault conditions
• standard VMEbus-compatible 6U by 220 mm board installed
• Eurocard crate
• Two 96-pin I/O connectors

MCOR Modules

MCOR 2/6/9/12

Each module can be customized to provide maximum outputs of 2 amps, 6 amps, 9 amps, and 12 amps. Up to 16 of these can fit in a single 6U VME style crate.

MCOR 30

Each module can provide a maximum output 30 amps. Up to 8 of these can fit in a single 6U VME style crate.

The Hi-Techniques FreeStyle series of Data Acquisition Systems is a versatile, capable solution for mobile and rugged data acquisition applications. FreeStyle was designed from the ground up to make data acquisition as fast and as easy as possible. Just grab your FreeStyle and your computer and head out to the test site.

Flexibility by Design