Products

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +30 to -30 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510R30 MCOR30 Power Modules are identical and interchangeable
  • Programming Card is plugged into the replacement module.
• Each channel has a critically-damped, LC noise filter with a cut-off frequency of about 8 kHz.
• A 16-pin front panel diagnostics connector taps onto major circuit nodes which enables quick “inthe-crate” fault evaluation

• 2U Chassis – 19″ rack mount 3.48” Height, 9.60” Depth and Weight 6lb.
• Power 120V AC 60Hz
• Washable front removable air filter
• Ball Bearing AC fans provide 330 CFM
• Dual plenum design
• Cooling for 160mm,220mm depth modules
• Diverts lower warmed air to rear of Cabinet
• RM option diverts lower air to front of Cabinet

• accommodate these control schemes
• total control system interface on a single VME-standard card
• occupies the left-most slot of the crate
• monitoring voltage reference inputs, output voltages and fault conditions
• standard VMEbus-compatible 6U by 220 mm board installed
• Eurocard crate
• Two 96-pin I/O connectors

MCOR Modules

MCOR 2/6/9/12

Each module can be customized to provide maximum outputs of 2 amps, 6 amps, 9 amps, and 12 amps. Up to 16 of these can fit in a single 6U VME style crate.

MCOR 30

Each module can provide a maximum output 30 amps. Up to 8 of these can fit in a single 6U VME style crate.

• provides precision bi-polar output currents
• minimal zero-cross over distortion
• 19” rack mounted 6U x 220 mm crate
• crate has 17 slots; 16 (slot 0 thru 15)
• connectors
  • J1 (ExtIntlk),
  • J2 (CrateOK),
  • J3 (Input Reference Voltages),
  • J4 (Output Monitors), and
  • J9 (Bitbus)

• Dynamic set up: During a simple frame reading, users can define elements to be acquired, recorded, visualized and surveyed in real time.
•  Macro-command: Users can write and execute complex test sequences thanks to macro-command functions.
•  Local & Distant Integration: AT-DIAG can be driven and interrogated by external software. It can also be used with a computer through Ethernet.
• Communication ports: Communication is done through RS232, NI CAN acq. Card, specific acquisition card or system.
•  Protocols: FREERUNNING, KWP2000, CAN, LIN, FlexRay, ARINC, … Possibility to implement new protocols (customized protocol, …).
•  Multi-product & Multi-protocol Communication: Communication can be set up with multiple addresses and protocols during a single test.

• 1 software for all your equipment
• 1 software for all standards
• 1 software for your electrical and EMC tests
• Advanced functions of monitoring and control
• Automated reports
• Team of specialists at your disposal

• Fast: ACA compression and parallelization allow to speed up the calculation
• Accurate: Fully validated with measurement results on real mock-up
• Innovative: New method from research labs
• Powerful: Compute very large models
• Easy: Dedicated graphical user interface with modern layout

• Fast: ACA compression and parallelization allow to speed up the calculation
• Accurate: Fully validated with measurement results on real mock-up
• Innovative: New method from research labs
• Powerful: Compute very large models
• Easy: Dedicated graphical user interface with modern layout

• Unique user interface for all tests
• Independent from any measuring device manufacturers
• Free drivers and over 500 supported devices
• Efficient and dedicated Technical support
• Wide range of supported standards (ENxx, CISPR, AUTOMOTIVE, DO160, …)
• Interface Agilent VEE™, WindowsLabView™, LabWindows CVI™, Visual C++
• Operating system: Win XP, Vista, Seven, Windows 8
• Report in MS Office™ 2003, 2007, 2010, 2013, Open office

Positional current probe,  PCB track Touch & Measure

Unique technology enabling current measurement in PCB tracks bandwidth of DC to 5MHz, dynamic range of 10mA to 20A pk-pk useable with any normal oscilloscope, safety rated to 300V Cat II,  investigates waveforms in any conductor including ground planes.

Bench/System DC Power Supplies, PowerFlex or PowerFlex+ regulated Single or Dual Outputs 1200 watts, with/without Digital Remote Interfaces

• Single or dual outputs, 1200 watts total
• PowerFlex design gives variable voltage/current combinations within a power envelope
• Up to 60 volts or 80 volts and up to 50 amps
• Setting by direct numeric entry or by spin wheel
• High setting resolution of 1mV in up to 60 volts
• Low noise of < 3mV rms at full power
• Bench or rack mounting, front and rear terminals
• Quasi analogue remote control
• RS232, USB GPIB & LAN interfaces (P models)

Bench/System DC Power Supply, PowerFlex Regulation, Smart Analog Controls Single or Dual Outputs, 360 to 840 watts, with/without Remote Interfaces

• PowerFlex design gives variable voltage and current combinations within a maximum power range
• Up to 60 volts and up to 20 amps
• 180 watts or 420 watts maximum per output
• Isolated outputs can be wired in series or parallel
• Constant voltage or constant current operation
• Settings Locking (S-Lock)
• PowerFlex or fixed-range operation
• Variable OVP trips
• Selectable remote sense terminals
• Compact quarter or half rack 3U case size
• Isolated analogue remote control (CPX400SA only)
• RS232, USB, GPIB & LXI compliant LAN (P models only)

Bench/System DC Power Supply, Multi-Range, Digital Control Triple Outputs, 315 or 378W with/without Remote Interfaces

• Three high performance outputs each with full functionality
• Range switching gives variable voltage/current combinations
• Shared power mode provides double power from a single output
• Low output noise and ripple via linear final regulation
• High setting resolution of up to 1mV and 0.1mA
• Variable OVP and OCP trips on all outputs
• 50 setting memories per output plus 50 linked memories
• Selectable voltage tracking (isolated tracking)
• Selectable current meter averaging
• Switchable remote sense capability
• Graphic LCD provides simultaneous output metering
• Numeric or spin-wheel control of all parameters
• Individual or combined output on/off control with
• programmable delay sequencing.
• 3U half-rack case for bench or rack mounting
• GPIB, RS-232, USB and LAN (LXI) interfaces (-P models)
• Duplicate power & sense terminals at rear (-P models)

MX100T and MX100TP:

• 315 watts total power
• Three outputs of equal power, each capable of 35V at 3A
• Range switching provides up to 70 volts and up to 6 amps

MX180T and MX180TP:

• 375 watts plus of total power
• Two high power outputs plus one low power output
• High power outputs each capable of 30 volts at 6 amps
• Range switching provides up to 120 volts or up to 20 amps
• Low power output provides up to 12 volts or up to 3 amps

Bench/System DC Power Supply, Single Output, Mixed-mode Regulation up to 360 watts, with/without remote interfaces

• Compact & lightweight power supply
• 0 to 18V at 0 to 20A or 0 to 35V at 0 to 10A
• Bench or rack mounting, front & rear terminals
• Very low noise, excellent transient response
• Comprehensive protection including OVP trip
• High setting resolution, remote sense terminals
• Analogue controls

P versions add:

• RS-232 and GPIB interfaces as standard
• Keyboard setting of all parameters
• Rotary and delta (step) control of V and I
• Watts display, non-volatile storage of 25 settings
• Fully programmable with bus readback of V & I

Bench/System High Precision DC Power Supply, Linear Regulation, Digital Control Single or Triple Outputs, 105 to 242 watts, with/without Remote Interfaces

• Advanced dc power supplies, single or triple output
• Up to 112 watts per output
• Very high precision, very low noise, excellent dynamics
• Advanced user interface with numeric and rotary control
• Multiple voltage/current ranges for increased flexibility
• Multiple non-volatile memories for power supply set-ups
• Switchable remote sense provides perfect load regulation
• Comprehensive protection including OVP and OCP trips
• Compact bench footprint; modular width for rack mounting
• Auxiliary output fully variable 1.00V to 6.00V at 3A with selectable voltage and current metering (T models)
• Bus programmable via USB, RS232, GPIB or LAN (P models)
• LAN interface is LXI compliant
• Duplicate power and sense terminals at rear (P models)