Products

The FMC-MOTDRV22 Motor Driver is a cost efficient dual channel stepper motor control board designed for systems that require reliable motion control within an FPGA based environment. Built according to the ANSI VITA 57.1 FMC standard, this mezzanine card enables precise control of bipolar stepper motors while providing integrated diagnostics and protection features. With programmable chopper modes, motor load detection, and flexible voltage options, the FMC-MOTDRV22 Motor Driver offers a dependable solution for automation, instrumentation, and scientific motion control systems.

Key Features

• Dual channel stepper motor driver design
• Compatible with ANSI VITA 57.1 FMC standard carrier boards
• Supports bipolar stepper motors for precision motion control
• Maximum output up to 12 V or 24 V at 1.8 A per coil depending on model
• Programmable chopper slope with three operating modes
• Integrated motor load detection without external sensors
• Load dependent current control for efficient motor operation
• Diagnostic monitoring and system protection features
• Protection against overcurrent, short to ground, undervoltage and overheating
• Encoder interface support for motor position monitoring
• Flexible configuration with internal or external power supply options
• Dedicated cabling solutions available for easy installation

The FMC-PICO-1M4 Ammeter is a high precision four channel current measurement board designed for accurate monitoring of very low bipolar currents in advanced electronic systems. Built as a Low Pin Count FPGA Mezzanine Card compliant with the VITA 57.1 FMC standard, this module combines high resolution data acquisition with low latency performance. With 20 bit resolution and sampling speeds up to 1 MSPS, the FMC-PICO-1M4 Ammeter provides reliable current monitoring for scientific instrumentation, accelerator systems, and precision measurement environments.

Key Features

• Four channel high precision floating ammeter design
• 20 bit resolution analog to digital conversion
• Sampling rate up to 1 MSPS for fast data acquisition
• Independent and simultaneous sampling for each channel
• Multiple measurement ranges depending on board version
• Bipolar current measurement capability
• Floating input channels up to ±300 V relative to FMC ground
• Low noise analog front end for precise measurements
• Minimal temperature dependence for stable performance
• Optional factory calibration with EEPROM stored calibration data
• External trigger support for synchronized acquisition
• Separate SPI communication links for each channel
• Compatible with VITA 57.1 FMC Low Pin Count carrier boards

Compact, versatile, and efficient, the FX Series is ideal for test labs, R&D, and educational use.

Key Features:

• PowerFlex autoranging outputs (up to 105W per channel)
• Dual or triple output models (210W or 246W total)
• SELV compliant and high safety design
• Rotary, touch, and USB control options
• Low ripple noise (<2mV), high resolution (1mV/1mA)
• Voltage tracking and simultaneous V/I control
• Remote USB interface with SCPI protocol
• 25 user-defined memory presets
• Switchable remote sense & intelligent cooling
• Includes Test Bridge software for logging & automation

The HV-PANDA HV Board is a high voltage Advanced Mezzanine Card designed for MTCA.4 systems that require reliable and precise high voltage delivery. This double width AMC board integrates four independent high voltage channels capable of delivering up to 6 kV output. Built using proven high voltage technology, the HV-PANDA HV Board ensures stable operation and secure power control for detector and instrumentation applications. With integrated safety interlocks, flexible channel configurations, and dedicated monitoring software, the board offers a dependable solution for advanced scientific and industrial systems.

Key Features

• Double width AMC board designed for MTCA.4 systems
• Four independent high voltage channels
• Maximum output up to 6 kV per channel depending on configuration
• Multiple channel rating options including 6 kV, 4 kV, and 500 V
• Maximum power up to 6 W per channel
• Positive or negative polarity configuration available
• Front panel interlocks for individual channel safety control
• Additional 12 V power input for high voltage operation
• RTM interface for MTCA backplane connectivity
• Reliable high voltage technology for detector applications
• Graphical user interface for simple system control
• Dedicated drivers for configuration and monitoring

• Current measurement from insulated probing of conductor
• Suitable for observation and measurement of current in PCB tracks, component leads and ground planes
• Wide dynamic range of 10mA to 20A peak to peak
• Wide bandwidth of DC to 5MHz
• Low noise figure equivalent to <6mA rms at full B/W
• Safety rated to 300V Cat II (600V Cat 1)
• Suitable for connection to any oscilloscope
• High accuracy general purpose H-field probe
• Converts to ‘closed magnetic circuit’ current probe

The Aim-TTi LCR400 Precision LCR Meter delivers high-accuracy component testing in a compact, user-friendly design. With 0.1% basic accuracy and built-in comparator functions, it’s ideal for precision component measurement and quality control.

Key Features:

• 0.1% basic measurement accuracy for reliable results
• Automatic component recognition for ease of operation
• Dual 5-digit high-brightness displays for clear readings
• Built-in 4-terminal component fixture for stable connections
• Limits comparator with 8 Pass bins and 2 Fail bins
• Three selectable test frequencies with switchable bias
• RS232 standard interface for PC connectivity
• Optional SMD tweezers, Kelvin clips, and PC logging software

The Aim-TTi LD400 Series DC Electronic Load is a versatile and high-performance solution for testing DC power supplies, batteries, and converters. With precise control, multiple operating modes, and advanced transient testing, it ensures dependable and accurate performance for laboratory and production environments.

Key Features:

• Wide operating range: 0–80V and 0–80A
• 400W continuous and 600W short-term power dissipation
• Multiple modes: constant current, voltage, resistance, conductance, and power
• Operates at <1V for high-current testing up to 40A
• Built-in transient generator with variable slew rate
• High accuracy with fine-level setting resolution
• Variable drop-out voltage for battery discharge testing
• Graphical LCD with intuitive soft-key control
• Analog and TTL remote control functions
• USB, RS232, and LAN (LXI) interfaces; optional GPIB (LD400P)
• Front and rear input terminals for flexible connections

The Aim-TTi LDH400 Series DC Electronic Load offers a powerful and precise solution for direct testing of DC power sources, converters, and PFCs. Designed for high-voltage applications, it combines advanced features, intuitive control, and reliable performance in a compact form factor.

Key Features:

• Wide voltage range: 10V to 500V and current up to 16A
• 400W continuous power dissipation at 28°C (360W at 40°C)
• Operates in constant current, resistance, conductance, and power modes
• High accuracy and resolution for precise level settings
• Built-in transient generator with adjustable slew rates
• Variable drop-out voltage ideal for battery and power testing
• Graphical LCD with easy soft-key interface
• Front and rear input terminals for flexible connectivity
• Remote control via USB, RS232, and LXI-compliant LAN
• Optional GPIB interface available
• Rated to CAT II (300V) safety standards

• Three or four high performance outputs each with full functionality
• Range switching gives variable voltage/current combinations
• Shared power mode provides double power from a single output
• Low output noise and ripple via linear final regulation
• High setting resolution of up to 1mV and 0.1mA
• Variable OVP and OCP trips on all outputs which can be linked (MX-Q Series 2 units only)
• Individual or combined output on/off control with programmable delay sequencing.
• Selectable voltage tracking (isolated tracking)
• Selectable current meter averaging
• Switchable remote sense capability
• Graphic LCD (colour on Series 2) provides simultaneous output metering
• Numeric or spin-wheel control of all parameters
• 50 setting memories per output plus 50 linked memories
• 3U rack case for bench or rack mounting (4U rack kit accessory available)
• RS-232, USB and LAN (LXI) interfaces (P models)
• GPIB option (P models only)
• Duplicate power & sense terminals at rear (P models)
• Software control from Test Bridge software (free download – P models only)

Series 2 (“S2”) models add:

• Colour display
• Enhanced channel power sharing
• ‘TripLink’ feature: Link channels to trip together on OVP or OCP
• New MX103Q SELV Model

The NGPS Power Supply is a high stability digital power supply series designed for demanding industrial and scientific applications. Delivering up to 10 kW of output power and scalable up to 40 kW through parallel operation, this advanced system provides precise current and voltage control with exceptional temperature stability. Equipped with Gigabit Ethernet connectivity, an embedded web server, waveform generation capability and a built in oscilloscope, the NGPS Power Supply offers a powerful and flexible solution for laboratories, research facilities and high performance power systems.

Key Features

• High stability digital power supply with output power up to 10 kW
• Parallel operation capability allowing up to 40 kW system power
• Precise current and voltage control using advanced digital architecture
• Temperature stabilized internal section for extremely low drift
• High speed 10/100/1000 Mbit Ethernet communication
• Ultra fast SFP interface supporting update rates up to 100 kHz
• Embedded Linux operating system with web based configuration interface
• Built in Arbitrary Waveform Generation for custom signal control
• Integrated four channel oscilloscope for real time monitoring
• Remote sensing terminals for accurate voltage control at the load
• Optional analog control input for compatibility with legacy systems
• Low noise and high efficiency performance for demanding applications

Key Features

• Supports wafers up to 200 mm (optional 300 mm upgrade)
• Operates at cryogenic temperatures down to 10 K
• Semi-automated with optional full automation via autoloader
• Compatible with liquid nitrogen, liquid helium, or cryo-cooler
• Ice- and condensation-free probing for stable performance
• Up to eight probe positioners or probe card integration
• Solid vibration-isolated frame for precision measurements
• Velox software with intuitive alignment and automation

The Aim-TTi PL Series DC Power Supply combines precision, flexibility, and reliability in a compact linear regulated design. Available in single, dual, and triple output configurations, it delivers exceptional control and accuracy for laboratory, R&D, and testing environments.

Key Features:

• Single, dual, or triple output models
• Voltage range from 6V/8A to 60V/1.5A
• High-performance linear regulation for low noise
• Compact and space-saving design
• True analog controls for smooth operation
• S-Lock function to instantly lock settings
• V-Span feature to customize voltage range
• Low current measurement and meter averaging
• Selectable remote sense terminals
• Independent, Isolated Tracking, and True Parallel modes
• High current, low voltage output on triple models
• Optional interfaces: RS-232, USB, LAN (LXI), and GPIB
• Analog remote control of voltage and current (single output only)

Key Features

• Entry-level manual wafer probing in vacuum < 1×10⁻⁴ mbar
• Supports wafers up to 150 mm or single dies
• Up to six probe positioners for flexible testing
• Optional thermal chuck from -60°C to +300°C
• Probing possible with open chamber lid at atmosphere
• Stable, vibration-isolated frame for precise results
• Ergonomic design with hinged topside lid for easy access
• Independent control of chuck stage and positioners
• Fast, manual step-and-repeat wafer testing

Cascade PM300 – 300 mm Analytical Probe Station

Key Features:

• Industry benchmark for manual wafer probing and failure analysis.
• Superior mechanical stability with granite base for precision and repeatability.
• High-precision probe positioning with independent X-Y coarse and fine adjustments.
• Configurable for DC, RF, mmW, WLR, FA, and 3D IC testing.
• Wide thermal range: -60°C to +200°C (PM300PS) / +15°C to +300°C (PM300).
• Optional electromagnetic shielding (PM300PS) for ultra-low-noise environments.
• Spacious, ergonomic design supporting up to 12 positioners.
• Upgradeable platform to support future testing needs.

The Polarity Inverters series provides a reliable solution for switching the output polarity of high power converters. Designed to work seamlessly with monopolar power supplies such as NGPS systems, these polarity switching units support current ratings up to 1000 A and voltage up to 250 V. With integrated safety interlocks and enabling signals, the system ensures secure polarity inversion for demanding industrial and scientific applications.

Key Features

• Reliable polarity switching for power converters up to 1000 A
• Maximum voltage rating of 250 V for high power applications
• Compatible with monopolar power supplies including NGPS systems
• Available in multiple current ratings including 200 A, 420 A, 630 A and 1000 A
• Auxiliary AC power input from 100 to 240 VAC at 50 or 60 Hz
• Integrated interlock and enabling signals for safe switching operations
• Supports control signals up to 240 V at 16 A and 10 A
• Designed for applications requiring polarity reversal such as magnet degaussing
• Standard rack mounting design with 19 inch enclosure options
• Durable industrial construction for reliable long term operation

The PS1112S Power Supply is a compact low noise power supply designed to deliver stable 12 V output for sensitive measurement and instrumentation systems. Built with a mixed switching linear architecture, this high efficiency unit ensures extremely low ripple and noise levels that help maintain measurement accuracy. With a maximum output power of 14 W and a robust stainless steel enclosure, the PS1112S Power Supply is an ideal solution for powering precision electronic devices and scientific instruments.

Key Features

• Low noise fixed voltage power supply with stable 12 V output
• Maximum output power of 14 W for precision electronic systems
• Maximum output current of 1.2 A depending on input conditions
• Mixed switching linear power architecture for low noise performance
• Extremely low ripple and noise in the DC to 1 MHz frequency range
• Compact and durable stainless steel enclosure
• Designed for accurate measurement and instrumentation systems
• High efficiency design while maintaining low noise operation
• Suitable for powering electrometers and precision measurement devices
• Optimized for laboratory and research equipment applications