Uncategorized

Single-phase, 2U, industrial amplifier/battery simulator

• Bench-sized
• Powered from 120V/230VAC
• Source and Sink (4 quadrant)
• Rugged Design
• 3-Year, No-Fault Warranty

Key Performance Capabilities:

• Drop outs and surges as fast as 1.2µs
• Small signal response up to 1 MHz
• 13.5 VDC at up to 28A
• Field-selectable ±40V, 75V or 150V potential

The First Wide-Bandwidth, High-Power Digital Amplifiers

• Max Continuous Output Current: 300A RMS
• Surge Rating: 2X power at up to 400 V_P or 750A
• Apparent Power Rating: Up to 5X continuous power rating atup to 400 V_P or 750A
• Supply Voltage: Three-phase, 208V ±10%, 60A, 50/60 Hz; 400V ±10%, 15A version available.
• Dimensions (HxWxD): 36.5 x 21.0 x 30.75 inches (92.7 x 53.3 x 78.1 cm)
• Weight: Appx. 540 lbs. (244.9 kg)

The EMI 64k software allows to embed the TDEMI systems in a fully automated test environment.

• Full automation of EMI testing according to all commercial and military standards
• Automated control of turntable, antenna and other equipment
• Height and Angular Scan
• Procedures according to standards as well as customized procedures
• Reducing the cost for EMC and communication testing and certification by tailored packages

The measurement system for all emission measurments in the frequency range 1 Hz – 44 GHz.

• Frequency Range  1 Hz – 30MHz, 1GHz, 3GHz, 6GHz, 9GHz, 18GHz, 26GHz, 40 GHz and 44GHz
• 225 MHz Real-time Analysis Bandwidth
• Weighted Real-time Spectrogram up to 44 GHz
• CISPR Bandwidths 200 Hz, 9 kHz, 120 kHz, 1 MHz
• MIL/DO Bandwidths 10 Hz, 100 Hz, 1 kHz, 10 kHz, 100 kHz, 1 MHz

The measurement system for all emission measurments in the frequency range 1 Hz – 44 GHz.

• Full compliance EMI Reciever according to standard CISPR 16-1· 1, ANSI C63.2, MIL->461, and DO·160
• Spectrum Analyzer
• Integrated LOW Noise Ampllfier (lNAI)
• Integrated Preselect1on
• Tradttional and FFT·based Mode
• Automatic Stepped Attenuator
• Ultra Low Noise Floor
• Excellent spurious Performance
• Real-time Spectrum Analyzer optional
• Vast IQ-Bandwidth

TDEMI Mobile+. The ultra mobile EMI receiver – Emission measurements everytime, everywhere. Fully stand-alone operable.

• Frequency Ranges 10Hz – 1GHz, 3GHz, 6GHz or 7GHz
• 16000x faster than conventional receivers
• Super compact design and 12V supply
• 225 MHz fully gapless real-time analysis bandwidth
• Weighted Real-time Spectrogram

Ultra High Performance RT Spectrum Analyzer. Ultrafast EMI Measurements.

• Frequency Range from 1 Hz up to 50 GHz
• 225 MHz Real-time analysis bandwidth
• 100 dB Dynamic Range
• Ultrahigh performance preselection in all modes
• Up to 510 MHz Real-time IQ-Analysis bandwidth
• Ultra High Performance Spectrum Analyzer

• Compact, air-cooled OEM style
• Superior pulse repeatability
• Simple parallel operation for higher power
• Optional Active PFC (pf = 0.98)
• Full remote control interface
• High EMI-RFI immunity

• Advanced semiconductor technology
• High-quality construction
• Rapid capacitor and pulse-forming network charging
• Compact and lightweight design
• Simple parallel operation for higher power needs
• Compatible with worldwide input voltages and frequencies
• Fully adjustable output voltage
• Comprehensive remote control interface

• High-Speed Current Control: No dynamic overshoot or oscillation
• High Slew-Rate: Up to 30A/*s for fast load changes
• Low Voltage Operation: Stable operation with no turn-on delay
• Multi-Functional: Seven load modes and four operating modes
• Parallel Operation: Up to 10kW with 10 units
• User-Friendly Interface: Built-in USB and optional IEEE interfaces
• Compliance: EN61010-1 compliant with a two-year warranty

• 20 Amp Operation: Full performance with 20 amp service
• Automatic Power Reduction: Reduces power usage during idle periods
• Heat Only Mode: Reduces power usage when cold temperatures are not used
• WhisperStream Technology: quieter, smooth-sounding operation, 56 dBA
• Frost Free Test Environment: dry air purge for tester interface, prevents condensation:
  0.5 to 3scfm (0.25 to 1.5 l/s)
• Heated Defrost: quickly removes moisture buildup from internal chiller
• DUT Temperature Control : Proprietary control algorithm enables DUT temperature to be directly controlled
• Transition Rate*
  -55 to +125°C, approx. 10 seconds
  125 to -55°C, approx. 10 seconds
• System Airflow Output*
  4 to 18scfm (1.9 to 8.5 l/s) Continuous
• Temperature Range*
  -80 to +225°C (60Hz) No LN2 or LCO2 Required

• High reliability thermal cycling without thermoelectric modules
• Temperature range: -65 to 175°C
• Cooling power:
  • 40W at -40°C for lower power devices
  • 55W at -55°C and 120W at -40°C.
• Transition rate: up to <35 sec over 25 to -40°C
• Easy and secure thermal connection to in-circuit or test socked DUT
• Touch-screen controller: user-programmable temperatures, graphing, data logging
• Communications options: Ethernet, USB, IEEE, RS232

-60° to +200°C

• Economy model with high thermal capacity
• Precise temperatures with fast transitions from -60 to 200°C
• No annual leak testing required per EU 517/2014 F-Gas Regulation
• Effective testing and conditioning of electronic components, boards, and modules
• Available for 50 and 60Hz operation
• No need for Liquid Nitrogen (LN2) or Liquid Carbon Dioxide (LCO2)
• Remote communications and set up and touch screen operation
• User Defined Temperature Limits

Key Performance Capabilities:

• Slew rates up to 60 V/µsec.
• Up to 240A DC at +50VDC or –50VDC (4301-240 configuration).
• Can provide pulses of up to 800 amps at voltages of up to ±100V (4301-240 configuration).
• Adjustable compensation allows the system to maintain a 50V/2 µsec rise-time over a wide range of current outputs.

Key Performance Capabilities:

• Bandwidth: DC to 50 kHz
• Voltage: 0 to 250 V_RMS; 0 to 350 VDC
• Current: 100 to 500 A_RMS
• Distortion: 0.1%
• Power: 4 kW to 20 kW*Power levels up to 5X rated power when driving reactive loads
• High power efficiency and density

*Models available with output from 4 kW to 20 kW (capable of up to 125 kVA).

Key Performance Capabilities:

• 4-Quadrant – Can source and sink current
• ±80V – DC supply for 12V to 48V systems; meets 80V surge requirements
• 300 kHz Sine – DC ripple tests for all major standards
• 3µs Rise Time – Exceeds surge and dropout slew rate requirements
• 3mΩ DC Source Impedance – Out-performs ISO 7637-2 requirements
• Supports ground reference and supply offset testing required for ISO 16750-2 Sect. 4.8 and other similar standards