Products

The Memory HiCorder MR8848 is a rugged, high-speed data acquisition recorder designed for capturing critical transient events in demanding industrial and infrastructure environments.

Key Features

• Durable, shock-resistant portable design for field use
• Isolated analog channels for safe multi-system measurements
• 32 analog and 64 logic channels for complex signal analysis
• High-speed sampling to capture fast transient waveforms
• Large-capacity memory for long-duration recording
• Built-in waveform and numerical analysis for pass or fail judgments
• Optional on-site printer for secure, tamper-proof documentation

The Memory HiCorder MR8870 is a compact, high-speed data acquisition recorder designed for waveform observation and RMS variation recording in maintenance and fault analysis applications.

Key Features

• Dual recording mode for instantaneous waveforms and RMS variations
• Two isolated analog channels with 2 MW internal memory
• Real-time saving of measured values to CF card
• Synchronize two instruments to record four channels at once
• High-speed performance up to 1 MS per second
• Compact handheld design for easy field transport
• Sharp QVGA TFT wide LCD for clear waveform viewing
• Ideal for elevator, motor, inverter, and machine diagnostics

The Memory HiCorder MR8875 is a high-speed, portable data acquisition recorder designed for vehicle testing, performance evaluation, and advanced multichannel measurements.

Key Features

• 1000 V direct input with instantaneous DC and RMS measurement
• Up to 16 to 60 channels with plug-and-play input modules
• High-speed simultaneous logging down to 2 microseconds
• Real-time recording directly to SD card for long-term logging
• 16-bit high-resolution measurement for accurate results
• Direct CAN bus input for onboard vehicle analysis
• Built-in FFT and waveform calculation for advanced analysis
• Intuitive touch screen interface for fast setup and operation
• Designed to withstand vibration and extreme temperatures

The Memory HiCorder MR8880 is a rugged, field-ready waveform recorder designed to capture high- and low-voltage signals safely in industrial and maintenance applications.

Key Features

• Direct 600 V input for three-phase power measurements
• CAT III 600 V isolation for safe high-voltage testing
• Four completely isolated analog channels
• Simultaneous recording of three-phase systems plus one spare channel
• Wide operating temperature range from minus 10 to 50 degrees Celsius
• Shock- and vibration-resistant housing with side protectors
• Built-in trigger and pre-trigger functions for precise event capture
• Presets function for fast and consistent setup

The Pulse Generator MR8791 is a plug-and-play input module for Hioki Memory HiCorders, designed for precise control simulation testing of electronic control systems.

Key Features

• Outputs pulse and pattern waveforms on up to eight channels
• Supports TTL level and open-collector output signals
• Designed for control simulation testing of ECUs and control boards
• Suitable for engine, airbag, brake, and power steering systems
• Wide frequency range for pulse and logic pattern generation
• Built-in self-test function for reliable operation
• Isolated design between unit and output channels
• Compact form factor for laboratory and test bench integration

Key Features:

• PXI/cPCI JTAG controller for seamless integration into PXI-based test systems
• Supports up to 4 JTAG chains on a Unit Under Test (UUT)
• Configurable I/O pin-out for maximum flexibility across projects
• Fully compatible with other XJLink2 controllers
• TCK clock speeds up to 166 MHz
• Programmable voltage domains from 1.1 V to 3.3 V in 0.1 V steps
• Built-in voltage meter and frequency counter on all I/O pins
• Adjustable signal termination with auto-skew control
• Includes LabVIEW™ Virtual Instruments (VIs) for easy integration
• Self-contained licence for use on multiple PXI racks or servers

The VIR Generator U8794 is a high-precision signal generation unit designed to simulate sensor outputs for ECU inspection, component testing, and maintenance applications.

Key Features

• Generates DC voltage, DC current, and resistance simulation signals
• Ideal for ECU inspection, electronic component testing, and equipment maintenance
• Eight fully isolated output channels for safe multi-signal simulation
• High-accuracy resistance simulation with automatic current calculation
• Designed exclusively for use with Memory HiCorder MR8740 series
• Supports sensor simulation testing without physical sensors
• Compact and lightweight design for bench and field environments

The Waveform Generator U8793 is a plug-and-play module for Hioki Memory HiCorders that enables arbitrary waveform output and anomaly simulation for advanced testing scenarios.

Key Features

• Outputs arbitrary waveform signals on up to two channels
• Reproduces waveforms recorded with a Memory HiCorder up to 15 V
• Generates customized arbitrary waveforms up to 15 V output
• Built-in function generator and sweep function
• Isolated design between unit and outputs and between channels
• Supports anomaly simulation and scenario-based testing
• Includes Waveform Maker software for easy waveform creation
• Designed for use with compatible Hioki Memory HiCorder models

Key Features:

• Portable USB-C to JTAG controller with 40 I/O pins
• Supports up to 8 separate JTAG TAP chains with independent frequencies
• Compact and rugged aluminium casing for lab, production, or field use
• Configurable JTAG pin-out to suit any Unit Under Test (UUT)
• Electrical protection against –30 V to +30 V input
• Four programmable I/O voltages (1.2 V to 3.3 V, in 0.1 V steps)
• Built-in voltmeter and frequency counter on all pins
• High-speed operation with TCK up to 166 MHz
• USB bus-powered with locking Type-C connector
• Self-contained licence for maximum flexibility

Key Features:

• Compact USB JTAG controller for flexible board testing
• Supports up to 4 JTAG chains per UUT
• Lightweight, portable, and ideal for lab, production, or field use
• Configurable pin-out for easy adaptation to any PCB design
• High-speed TCK clock up to 166 MHz
• Two programmable voltages from 1.1 V to 3.3 V in 0.1 V steps
• Built-in voltmeter and frequency counter on all I/O pins
• +5 V tolerant signals with auto-skew control
• USB bus-powered, no external PSU needed
• Self-contained licence, usable on multiple PCs

Key Features

• Approved by Keysight Technologies for i3070 ICT integration
• Fully compatible with all XJTAG projects
• High-speed programming with TCK up to 166 MHz
• Supports up to 4 JTAG chain connections to UUT
• Configurable interface voltages (1.1 V to 3.3 V)
• Adjustable signal slew rate and drive strength
• Automatic signal skew control for maximum reliability
• Frequency counter on all I/O pins (up to 200 MHz input)
• Fits into one i3070 utility card slot (multiple units supported)
• Enables test + programming in a single stage to boost throughput
• Supports additional protocols including I²C, SPI, and vendor-specific interfaces
• Flexible software licensing options for stand-alone or network operation

Key Features:

• 4-port JTAG tester for simultaneous testing of up to 4 boards
• High-speed USB 2.0 interface with robust performance
• Supports up to 4 TAP chains per UUT
• Configurable JTAG pin-out for simplified connectivity
• Parallel or independent testing on each port
• Programmable voltages from 1.1 V to 3.3 V in 0.1 V steps
• Built-in voltmeter and frequency counter on all I/O pins
• Automatic signal skew control for reliable operation
• Self-contained licence for use across multiple PCs
• Ideal for production lines and PCB manufacturers

The EME Guard Plus is a lightweight and robust personal protection monitor designed to ensure the safety of workers operating near electromagnetic field (EMF) emitters such as antennas, radars, and base stations. With a frequency range of 1 MHz to 40 GHz, this device continuously monitors and records EMF exposure levels while providing immediate audio, visual, and vibrating alerts when exposure exceeds predefined safety thresholds. Customizable alarm settings and a triaxial isotropic probe ensure accurate and reliable measurements.

The EME Guard XS Radar is a state-of-the-art RF safety monitor, specifically designed for workers operating near radar transmitters and antennas. With its isotropic tri-axis E-field sensors, this compact device provides continuous EMF monitoring over a frequency range of 1 MHz to 40 GHz, including short pulsed signal detection. Equipped with audio and visual alarms, it alerts users instantly when EMF exposure exceeds predefined safety thresholds, creating a safer working environment for military, aviation, and telecom personnel.

Solutions For:

•  Accurate measurement with tri-axis sensors
• Instant audio and visual alarm
• Robust, reliable and user-friendly
• Covers 5G / 6G bands, measuring up to 71 GHz

User profile:

• Persons working near antennas including installation and maintenance workers, broadcast, PMR and mobile phone operators or regulatory body employees

Measurement capabilities:

• Continuous monitoring of Electromagnetic Field levels with isotropic tri-axis E-field sensors
• EMF Level indicated by a LED color scale
• Audio and visual alarms triggered when EMF exceeds the reference level

• HD4096 technology provides 12-bit resolution up to 8 GHz and 20 GS/s
• Up to 5 Gpts of acquisition memory enables detailed viewing of long events
• 15.6” 1900 x 1080 Full HD capacitive touchscreen
• ProBus2 input supports up to 8 GHz bandwidth while maintaining support for legacy ProBus probes
• MAUI with OneTouch user interface for intuitive and efficient operation
• Waveform Control Knobs – Control channel, zoom, math and memory traces with the multiplexed vertical and horizontal knobs
• Color-coded panel indicators – Trigger, horizontal and vertical indicator colors correspond to the associated waveform on the display
• Cursor/Adjust Knobs – Enable and position cursors or adjust settings and parameters without opening a menu
• Mixed Signal Capability – Debug complex embedded designs with integrated 16-channel mixed signal capability
• Easy connectivity with seven USB 3.1 ports (3 front, 4 side) and UHD (4k) HDMI and DisplayPort outputs