Products

The Memory HiCorder MR8848 is a rugged, high-speed data acquisition recorder designed for capturing critical transient events in demanding industrial and infrastructure environments.

Key Features

• Durable, shock-resistant portable design for field use
• Isolated analog channels for safe multi-system measurements
• 32 analog and 64 logic channels for complex signal analysis
• High-speed sampling to capture fast transient waveforms
• Large-capacity memory for long-duration recording
• Built-in waveform and numerical analysis for pass or fail judgments
• Optional on-site printer for secure, tamper-proof documentation

The Memory HiCorder MR8870 is a compact, high-speed data acquisition recorder designed for waveform observation and RMS variation recording in maintenance and fault analysis applications.

Key Features

• Dual recording mode for instantaneous waveforms and RMS variations
• Two isolated analog channels with 2 MW internal memory
• Real-time saving of measured values to CF card
• Synchronize two instruments to record four channels at once
• High-speed performance up to 1 MS per second
• Compact handheld design for easy field transport
• Sharp QVGA TFT wide LCD for clear waveform viewing
• Ideal for elevator, motor, inverter, and machine diagnostics

The Memory HiCorder MR8875 is a high-speed, portable data acquisition recorder designed for vehicle testing, performance evaluation, and advanced multichannel measurements.

Key Features

• 1000 V direct input with instantaneous DC and RMS measurement
• Up to 16 to 60 channels with plug-and-play input modules
• High-speed simultaneous logging down to 2 microseconds
• Real-time recording directly to SD card for long-term logging
• 16-bit high-resolution measurement for accurate results
• Direct CAN bus input for onboard vehicle analysis
• Built-in FFT and waveform calculation for advanced analysis
• Intuitive touch screen interface for fast setup and operation
• Designed to withstand vibration and extreme temperatures

The Memory HiCorder MR8880 is a rugged, field-ready waveform recorder designed to capture high- and low-voltage signals safely in industrial and maintenance applications.

Key Features

• Direct 600 V input for three-phase power measurements
• CAT III 600 V isolation for safe high-voltage testing
• Four completely isolated analog channels
• Simultaneous recording of three-phase systems plus one spare channel
• Wide operating temperature range from minus 10 to 50 degrees Celsius
• Shock- and vibration-resistant housing with side protectors
• Built-in trigger and pre-trigger functions for precise event capture
• Presets function for fast and consistent setup

The Pulse Generator MR8791 is a plug-and-play input module for Hioki Memory HiCorders, designed for precise control simulation testing of electronic control systems.

Key Features

• Outputs pulse and pattern waveforms on up to eight channels
• Supports TTL level and open-collector output signals
• Designed for control simulation testing of ECUs and control boards
• Suitable for engine, airbag, brake, and power steering systems
• Wide frequency range for pulse and logic pattern generation
• Built-in self-test function for reliable operation
• Isolated design between unit and output channels
• Compact form factor for laboratory and test bench integration

Key Features:

• PXI/cPCI JTAG controller for seamless integration into PXI-based test systems
• Supports up to 4 JTAG chains on a Unit Under Test (UUT)
• Configurable I/O pin-out for maximum flexibility across projects
• Fully compatible with other XJLink2 controllers
• TCK clock speeds up to 166 MHz
• Programmable voltage domains from 1.1 V to 3.3 V in 0.1 V steps
• Built-in voltage meter and frequency counter on all I/O pins
• Adjustable signal termination with auto-skew control
• Includes LabVIEW™ Virtual Instruments (VIs) for easy integration
• Self-contained licence for use on multiple PXI racks or servers

The VIR Generator U8794 is a high-precision signal generation unit designed to simulate sensor outputs for ECU inspection, component testing, and maintenance applications.

Key Features

• Generates DC voltage, DC current, and resistance simulation signals
• Ideal for ECU inspection, electronic component testing, and equipment maintenance
• Eight fully isolated output channels for safe multi-signal simulation
• High-accuracy resistance simulation with automatic current calculation
• Designed exclusively for use with Memory HiCorder MR8740 series
• Supports sensor simulation testing without physical sensors
• Compact and lightweight design for bench and field environments

The Waveform Generator U8793 is a plug-and-play module for Hioki Memory HiCorders that enables arbitrary waveform output and anomaly simulation for advanced testing scenarios.

Key Features

• Outputs arbitrary waveform signals on up to two channels
• Reproduces waveforms recorded with a Memory HiCorder up to 15 V
• Generates customized arbitrary waveforms up to 15 V output
• Built-in function generator and sweep function
• Isolated design between unit and outputs and between channels
• Supports anomaly simulation and scenario-based testing
• Includes Waveform Maker software for easy waveform creation
• Designed for use with compatible Hioki Memory HiCorder models

Key Features:

• Portable USB-C to JTAG controller with 40 I/O pins
• Supports up to 8 separate JTAG TAP chains with independent frequencies
• Compact and rugged aluminium casing for lab, production, or field use
• Configurable JTAG pin-out to suit any Unit Under Test (UUT)
• Electrical protection against –30 V to +30 V input
• Four programmable I/O voltages (1.2 V to 3.3 V, in 0.1 V steps)
• Built-in voltmeter and frequency counter on all pins
• High-speed operation with TCK up to 166 MHz
• USB bus-powered with locking Type-C connector
• Self-contained licence for maximum flexibility

Key Features:

• Compact USB JTAG controller for flexible board testing
• Supports up to 4 JTAG chains per UUT
• Lightweight, portable, and ideal for lab, production, or field use
• Configurable pin-out for easy adaptation to any PCB design
• High-speed TCK clock up to 166 MHz
• Two programmable voltages from 1.1 V to 3.3 V in 0.1 V steps
• Built-in voltmeter and frequency counter on all I/O pins
• +5 V tolerant signals with auto-skew control
• USB bus-powered, no external PSU needed
• Self-contained licence, usable on multiple PCs

Key Features

• Approved by Keysight Technologies for i3070 ICT integration
• Fully compatible with all XJTAG projects
• High-speed programming with TCK up to 166 MHz
• Supports up to 4 JTAG chain connections to UUT
• Configurable interface voltages (1.1 V to 3.3 V)
• Adjustable signal slew rate and drive strength
• Automatic signal skew control for maximum reliability
• Frequency counter on all I/O pins (up to 200 MHz input)
• Fits into one i3070 utility card slot (multiple units supported)
• Enables test + programming in a single stage to boost throughput
• Supports additional protocols including I²C, SPI, and vendor-specific interfaces
• Flexible software licensing options for stand-alone or network operation

Key Features:

• 4-port JTAG tester for simultaneous testing of up to 4 boards
• High-speed USB 2.0 interface with robust performance
• Supports up to 4 TAP chains per UUT
• Configurable JTAG pin-out for simplified connectivity
• Parallel or independent testing on each port
• Programmable voltages from 1.1 V to 3.3 V in 0.1 V steps
• Built-in voltmeter and frequency counter on all I/O pins
• Automatic signal skew control for reliable operation
• Self-contained licence for use across multiple PCs
• Ideal for production lines and PCB manufacturers

• HD4096 technology provides 12-bit resolution up to 8 GHz and 20 GS/s
• Up to 5 Gpts of acquisition memory enables detailed viewing of long events
• 15.6” 1900 x 1080 Full HD capacitive touchscreen
• ProBus2 input supports up to 8 GHz bandwidth while maintaining support for legacy ProBus probes
• MAUI with OneTouch user interface for intuitive and efficient operation
• Waveform Control Knobs – Control channel, zoom, math and memory traces with the multiplexed vertical and horizontal knobs
• Color-coded panel indicators – Trigger, horizontal and vertical indicator colors correspond to the associated waveform on the display
• Cursor/Adjust Knobs – Enable and position cursors or adjust settings and parameters without opening a menu
• Mixed Signal Capability – Debug complex embedded designs with integrated 16-channel mixed signal capability
• Easy connectivity with seven USB 3.1 ports (3 front, 4 side) and UHD (4k) HDMI and DisplayPort outputs

• Eye diagram (a), eye mask failure (b) and IsoBER eye opening analysis (c)
• Jitter spectrum (a) with noise floor display (b) and inverse FFT of the periodic jitter (c)
• Data dependent jitter (DDj) plot for each bit in synch with pattern (a) and with histogram (b)
• Time interval error (TIE) jitter track analysis
• Jitter histograms (a) with bathtub curves (b) and CDF plot (c)
• Intersymbol interference (ISI) plots pinpoint bit sequences that have high ISI and are sources of bit errors
• Jitter measurements table with full details for one or more “lanes” plus reference