Products

• Current measurement from insulated probing of conductor
• Suitable for observation and measurement of current in PCB tracks, component leads and ground planes
• Wide dynamic range of 10mA to 20A peak to peak
• Wide bandwidth of DC to 5MHz
• Low noise figure equivalent to <6mA rms at full B/W
• Safety rated to 300V Cat II (600V Cat 1)
• Suitable for connection to any oscilloscope
• High accuracy general purpose H-field probe
• Converts to ‘closed magnetic circuit’ current probe

The Memory HiCorder MR8848 is a rugged, high-speed data acquisition recorder designed for capturing critical transient events in demanding industrial and infrastructure environments.

Key Features

• Durable, shock-resistant portable design for field use
• Isolated analog channels for safe multi-system measurements
• 32 analog and 64 logic channels for complex signal analysis
• High-speed sampling to capture fast transient waveforms
• Large-capacity memory for long-duration recording
• Built-in waveform and numerical analysis for pass or fail judgments
• Optional on-site printer for secure, tamper-proof documentation

The Memory HiCorder MR8870 is a compact, high-speed data acquisition recorder designed for waveform observation and RMS variation recording in maintenance and fault analysis applications.

Key Features

• Dual recording mode for instantaneous waveforms and RMS variations
• Two isolated analog channels with 2 MW internal memory
• Real-time saving of measured values to CF card
• Synchronize two instruments to record four channels at once
• High-speed performance up to 1 MS per second
• Compact handheld design for easy field transport
• Sharp QVGA TFT wide LCD for clear waveform viewing
• Ideal for elevator, motor, inverter, and machine diagnostics

The Memory HiCorder MR8875 is a high-speed, portable data acquisition recorder designed for vehicle testing, performance evaluation, and advanced multichannel measurements.

Key Features

• 1000 V direct input with instantaneous DC and RMS measurement
• Up to 16 to 60 channels with plug-and-play input modules
• High-speed simultaneous logging down to 2 microseconds
• Real-time recording directly to SD card for long-term logging
• 16-bit high-resolution measurement for accurate results
• Direct CAN bus input for onboard vehicle analysis
• Built-in FFT and waveform calculation for advanced analysis
• Intuitive touch screen interface for fast setup and operation
• Designed to withstand vibration and extreme temperatures

The Memory HiCorder MR8880 is a rugged, field-ready waveform recorder designed to capture high- and low-voltage signals safely in industrial and maintenance applications.

Key Features

• Direct 600 V input for three-phase power measurements
• CAT III 600 V isolation for safe high-voltage testing
• Four completely isolated analog channels
• Simultaneous recording of three-phase systems plus one spare channel
• Wide operating temperature range from minus 10 to 50 degrees Celsius
• Shock- and vibration-resistant housing with side protectors
• Built-in trigger and pre-trigger functions for precise event capture
• Presets function for fast and consistent setup

The Pulse Generator MR8791 is a plug-and-play input module for Hioki Memory HiCorders, designed for precise control simulation testing of electronic control systems.

Key Features

• Outputs pulse and pattern waveforms on up to eight channels
• Supports TTL level and open-collector output signals
• Designed for control simulation testing of ECUs and control boards
• Suitable for engine, airbag, brake, and power steering systems
• Wide frequency range for pulse and logic pattern generation
• Built-in self-test function for reliable operation
• Isolated design between unit and output channels
• Compact form factor for laboratory and test bench integration

The VIR Generator U8794 is a high-precision signal generation unit designed to simulate sensor outputs for ECU inspection, component testing, and maintenance applications.

Key Features

• Generates DC voltage, DC current, and resistance simulation signals
• Ideal for ECU inspection, electronic component testing, and equipment maintenance
• Eight fully isolated output channels for safe multi-signal simulation
• High-accuracy resistance simulation with automatic current calculation
• Designed exclusively for use with Memory HiCorder MR8740 series
• Supports sensor simulation testing without physical sensors
• Compact and lightweight design for bench and field environments

The Waveform Generator U8793 is a plug-and-play module for Hioki Memory HiCorders that enables arbitrary waveform output and anomaly simulation for advanced testing scenarios.

Key Features

• Outputs arbitrary waveform signals on up to two channels
• Reproduces waveforms recorded with a Memory HiCorder up to 15 V
• Generates customized arbitrary waveforms up to 15 V output
• Built-in function generator and sweep function
• Isolated design between unit and outputs and between channels
• Supports anomaly simulation and scenario-based testing
• Includes Waveform Maker software for easy waveform creation
• Designed for use with compatible Hioki Memory HiCorder models

High-Precision Current Measurement with BNC Connectivity

• Precision Current Sensing: ±1% accuracy ensures reliable real-time current monitoring.
• BNC Connector for Seamless Connectivity: Works with oscilloscopes, ADCs, spectrum analyzers, and power analyzers.
• Clamp-On Design for Non-Intrusive Measurement: Safely monitor live current flow without circuit disruption.
• 50 Ohm Termination Compatible: Output reduces by half when using a 50Ω termination.
• High-Voltage Safety Considerations: Conductive case requires adequate insulation for user safety.

The EME Guard Plus is a lightweight and robust personal protection monitor designed to ensure the safety of workers operating near electromagnetic field (EMF) emitters such as antennas, radars, and base stations. With a frequency range of 1 MHz to 40 GHz, this device continuously monitors and records EMF exposure levels while providing immediate audio, visual, and vibrating alerts when exposure exceeds predefined safety thresholds. Customizable alarm settings and a triaxial isotropic probe ensure accurate and reliable measurements.

The EME Guard XS Radar is a state-of-the-art RF safety monitor, specifically designed for workers operating near radar transmitters and antennas. With its isotropic tri-axis E-field sensors, this compact device provides continuous EMF monitoring over a frequency range of 1 MHz to 40 GHz, including short pulsed signal detection. Equipped with audio and visual alarms, it alerts users instantly when EMF exposure exceeds predefined safety thresholds, creating a safer working environment for military, aviation, and telecom personnel.

Solutions For:

•  Accurate measurement with tri-axis sensors
• Instant audio and visual alarm
• Robust, reliable and user-friendly
• Covers 5G / 6G bands, measuring up to 71 GHz

User profile:

• Persons working near antennas including installation and maintenance workers, broadcast, PMR and mobile phone operators or regulatory body employees

Measurement capabilities:

• Continuous monitoring of Electromagnetic Field levels with isotropic tri-axis E-field sensors
• EMF Level indicated by a LED color scale
• Audio and visual alarms triggered when EMF exceeds the reference level

HDO4000A oscilloscopes have 4 analog input channels, 12-bit resolution using Teledyne LeCroy’s HD4096 high-definition technology, up to 1 GHz of bandwidth and a compact form factor with a large 12.1” multi-touch display. They are ideal for debug and troubleshooting of power electronics designs, digital power management or power integrity analysis, automotive electronics systems, and deeply embedded or mechatronic designs.

The WaveSurfer 3000z has a 10.1″ capacitive touch display, the longest memory, and the deepest toolbox – all at an affordable price.

• HD4096 technology provides 12-bit resolution all the time
• 2ProBus input supports over 30 probes in 9 product categories
• 3Long record capture of up to 25 Mpts
• 412.1” 1280 x 800 HD capacitive touchscreen
• 5Mixed-signal capability – debug complex embedded designs with integrated 16-channel mixed signal option
• 6Easy connectivity with 2 USB 3.1 ports
• 7MAUI with OneTouch user interface for intuitive and efficient operation

• 15.6″ 1920 x 1080 capacitive touchscreen display
• 24 analog input channels
• 3ProBus input supports every Teledyne LeCroy probe
• 4MAUI with OneTouch user interface for intuitive and efficient operation
• 5Q-Scape multi-tab display architecture
• 6Up to 250 Mpts of acquisition memory
• 7HD4096 technology – 12 bits all the time
• 8Buttons/indicators color-coded to associated waveform on display
• 9Use cursors and adjust settings without opening a menu
• 10Mixed Signal capability with 16 integrated digital channels
• 116 USB 3.1 ports (2 front, 4 side)