Products

The Memory HiCorder MR8848 is a rugged, high-speed data acquisition recorder designed for capturing critical transient events in demanding industrial and infrastructure environments.

Key Features

• Durable, shock-resistant portable design for field use
• Isolated analog channels for safe multi-system measurements
• 32 analog and 64 logic channels for complex signal analysis
• High-speed sampling to capture fast transient waveforms
• Large-capacity memory for long-duration recording
• Built-in waveform and numerical analysis for pass or fail judgments
• Optional on-site printer for secure, tamper-proof documentation

The Memory HiCorder MR8870 is a compact, high-speed data acquisition recorder designed for waveform observation and RMS variation recording in maintenance and fault analysis applications.

Key Features

• Dual recording mode for instantaneous waveforms and RMS variations
• Two isolated analog channels with 2 MW internal memory
• Real-time saving of measured values to CF card
• Synchronize two instruments to record four channels at once
• High-speed performance up to 1 MS per second
• Compact handheld design for easy field transport
• Sharp QVGA TFT wide LCD for clear waveform viewing
• Ideal for elevator, motor, inverter, and machine diagnostics

The Memory HiCorder MR8875 is a high-speed, portable data acquisition recorder designed for vehicle testing, performance evaluation, and advanced multichannel measurements.

Key Features

• 1000 V direct input with instantaneous DC and RMS measurement
• Up to 16 to 60 channels with plug-and-play input modules
• High-speed simultaneous logging down to 2 microseconds
• Real-time recording directly to SD card for long-term logging
• 16-bit high-resolution measurement for accurate results
• Direct CAN bus input for onboard vehicle analysis
• Built-in FFT and waveform calculation for advanced analysis
• Intuitive touch screen interface for fast setup and operation
• Designed to withstand vibration and extreme temperatures

The Memory HiCorder MR8880 is a rugged, field-ready waveform recorder designed to capture high- and low-voltage signals safely in industrial and maintenance applications.

Key Features

• Direct 600 V input for three-phase power measurements
• CAT III 600 V isolation for safe high-voltage testing
• Four completely isolated analog channels
• Simultaneous recording of three-phase systems plus one spare channel
• Wide operating temperature range from minus 10 to 50 degrees Celsius
• Shock- and vibration-resistant housing with side protectors
• Built-in trigger and pre-trigger functions for precise event capture
• Presets function for fast and consistent setup

Experience precision RF signal analysis on the go with this lightweight, handheld analyzer designed for both lab and field use.

Key Features:

• Frequency range: 1MHz to 1.3GHz (PSA1303) or 2.7GHz (PSA2703)
• RBW: 300Hz to 10MHz
• -115dBm typical noise floor
• Dual markers with absolute/difference values
• AM/FM demodulation in zero span
• Auto-find & smart marker peak tracking
• USB for waveform saving and PC connection
• Live, View, and Reference trace modes
• 6-hour lithium-ion battery operation
• Weighs just 0.58 kg
• Optional U01 Upgrade: Limit lines, data logging, triggering, compensation tables

High-performance, battery-powered spectrum analyzers ideal for RF engineers and field use.

Key Features:

• Frequency range: 10MHz to 3.6GHz or 6.0GHz
• -120dBm typical noise floor
• Resolution bandwidths from 300Hz to 10MHz
• AM/FM audio demodulation with zero span
• Live, View & Reference traces with markers
• Smart marker tracking with peak detection
• USB data logging & real-time PC view
• Compact, lightweight (0.56 kg) with >3hr battery
• Optional U02 features: limit lines, OBW, ACPR, AM/FM waveform demodulation

The Pulse Generator MR8791 is a plug-and-play input module for Hioki Memory HiCorders, designed for precise control simulation testing of electronic control systems.

Key Features

• Outputs pulse and pattern waveforms on up to eight channels
• Supports TTL level and open-collector output signals
• Designed for control simulation testing of ECUs and control boards
• Suitable for engine, airbag, brake, and power steering systems
• Wide frequency range for pulse and logic pattern generation
• Built-in self-test function for reliable operation
• Isolated design between unit and output channels
• Compact form factor for laboratory and test bench integration

The Teledyne T3SA Series Spectrum Analyzers deliver high-performance signal analysis from 9 kHz to 3.2 GHz in a compact, easy-to-use design. Ideal for R&D, education, production, and pre-compliance testing, it features a large touchscreen and advanced digital IF technology.

Key Features:

• All Digital IF technology10.1”
• WVGA (1024 x 600) touchscreen display
• Frequency range from 9 kHz to 3.2 GHz
• -161 dBm/Hz displayed average noise level (typical)
• -98 dBc/Hz @ 10 kHz offset phase noise (typical)
• Total amplitude accuracy < 0.7 dB
• 1 Hz minimum resolution bandwidth (RBW)
• Built-in preamplifier for improved sensitivity

Typical Applications

● Research Laboratory
● Development Laboratory
● Repair and Maintenance
● Calibration Laboratory
● Automatic Production Test
● General bench-top use

The VIR Generator U8794 is a high-precision signal generation unit designed to simulate sensor outputs for ECU inspection, component testing, and maintenance applications.

Key Features

• Generates DC voltage, DC current, and resistance simulation signals
• Ideal for ECU inspection, electronic component testing, and equipment maintenance
• Eight fully isolated output channels for safe multi-signal simulation
• High-accuracy resistance simulation with automatic current calculation
• Designed exclusively for use with Memory HiCorder MR8740 series
• Supports sensor simulation testing without physical sensors
• Compact and lightweight design for bench and field environments

The Waveform Generator U8793 is a plug-and-play module for Hioki Memory HiCorders that enables arbitrary waveform output and anomaly simulation for advanced testing scenarios.

Key Features

• Outputs arbitrary waveform signals on up to two channels
• Reproduces waveforms recorded with a Memory HiCorder up to 15 V
• Generates customized arbitrary waveforms up to 15 V output
• Built-in function generator and sweep function
• Isolated design between unit and outputs and between channels
• Supports anomaly simulation and scenario-based testing
• Includes Waveform Maker software for easy waveform creation
• Designed for use with compatible Hioki Memory HiCorder models

High-Precision Current Measurement with BNC Connectivity

• Precision Current Sensing: ±1% accuracy ensures reliable real-time current monitoring.
• BNC Connector for Seamless Connectivity: Works with oscilloscopes, ADCs, spectrum analyzers, and power analyzers.
• Clamp-On Design for Non-Intrusive Measurement: Safely monitor live current flow without circuit disruption.
• 50 Ohm Termination Compatible: Output reduces by half when using a 50Ω termination.
• High-Voltage Safety Considerations: Conductive case requires adequate insulation for user safety.

HDO4000A oscilloscopes have 4 analog input channels, 12-bit resolution using Teledyne LeCroy’s HD4096 high-definition technology, up to 1 GHz of bandwidth and a compact form factor with a large 12.1” multi-touch display. They are ideal for debug and troubleshooting of power electronics designs, digital power management or power integrity analysis, automotive electronics systems, and deeply embedded or mechatronic designs.

The WaveSurfer 3000z has a 10.1″ capacitive touch display, the longest memory, and the deepest toolbox – all at an affordable price.

• HD4096 technology provides 12-bit resolution all the time
• 2ProBus input supports over 30 probes in 9 product categories
• 3Long record capture of up to 25 Mpts
• 412.1” 1280 x 800 HD capacitive touchscreen
• 5Mixed-signal capability – debug complex embedded designs with integrated 16-channel mixed signal option
• 6Easy connectivity with 2 USB 3.1 ports
• 7MAUI with OneTouch user interface for intuitive and efficient operation

• 15.6″ 1920 x 1080 capacitive touchscreen display
• 24 analog input channels
• 3ProBus input supports every Teledyne LeCroy probe
• 4MAUI with OneTouch user interface for intuitive and efficient operation
• 5Q-Scape multi-tab display architecture
• 6Up to 250 Mpts of acquisition memory
• 7HD4096 technology – 12 bits all the time
• 8Buttons/indicators color-coded to associated waveform on display
• 9Use cursors and adjust settings without opening a menu
• 10Mixed Signal capability with 16 integrated digital channels
• 116 USB 3.1 ports (2 front, 4 side)

• HD4096 technology provides 12-bit resolution up to 8 GHz and 20 GS/s
• Up to 5 Gpts of acquisition memory enables detailed viewing of long events
• 15.6” 1900 x 1080 Full HD capacitive touchscreen
• ProBus2 input supports up to 8 GHz bandwidth while maintaining support for legacy ProBus probes
• MAUI with OneTouch user interface for intuitive and efficient operation
• Waveform Control Knobs – Control channel, zoom, math and memory traces with the multiplexed vertical and horizontal knobs
• Color-coded panel indicators – Trigger, horizontal and vertical indicator colors correspond to the associated waveform on the display
• Cursor/Adjust Knobs – Enable and position cursors or adjust settings and parameters without opening a menu
• Mixed Signal Capability – Debug complex embedded designs with integrated 16-channel mixed signal capability
• Easy connectivity with seven USB 3.1 ports (3 front, 4 side) and UHD (4k) HDMI and DisplayPort outputs