Key Performance Capabilities:

• 4-Quadrant – Can source and sink current
• ±80V – DC supply for 12V to 48V systems; meets 80V surge requirements
• 300 kHz Sine – DC ripple tests for all major standards
• 3µs Rise Time – Exceeds surge and dropout slew rate requirements
• 3mΩ DC Source Impedance – Out-performs ISO 7637-2 requirements
• Supports ground reference and supply offset testing required for ISO 16750-2 Sect. 4.8 and other similar standards

Key Performance Capabilities:

• Up to 900 watts RMS power output (7136 model)
• Small signal response up to 400 kHz
• User-adjustable precision DC offset
• User-adjustable current limit: 1A to 25A
• 4-quadrant operation
• AC/DC coupled

Key Performance Capabilities:

• Up to 900 watts RMS power output (7136 model)
• Small signal response up to 400 kHz
• User-adjustable precision DC offset
• User-adjustable current limit: 1A to 25A
• 4-quadrant operation
• AC/DC coupled

• Frequency Range 10 Hz – 1GHz, 3GHz or 6GHz
• 4000x faster in your pre-certifcation work
• compact design and +12V power supply
• 162.5 MHz full gapless real-time analysis bandwidth
• Weighted Real-time Spectrogram

• requency Range from DC up to 40 GHz
• 685 MHz Real-time analysis bandwidth
• Dynamic range of more than 100 dB
• Multi-GHz real-time scanning up to 40 GHz
• all 6dB RBWs acc. to CISPR, MIL, DO, ANSI, FCC
• fastest super-heterodyn receiver on the planet

• compact and completely modular design
• high effectiveness in all operation modes, few requirements on building infrastructure
• ability to use an existing liquid cooling system directly
• optional matched liquid-to-air cooling unit TC.LAE available
• possibility of upgrading to systems of up to 1 MVA
• high level of system dynamics, ≤ 5 kHz modulation bandwidth
• non-restrictive capability of refeeding in the Q4 operation mode
• possibility of operating as an autonomous 4-Q and 3-phase quasi-analogue amplifier
• possibility of “Hardware-in-the loop”-operation (HIL mode)
• user friendly application software with pre-configured test patterns
• possibility of integrating into a complete SAS simulation and test system
• galvanic isolation available as an option without derating the simulator port data

Bidirectional (source & sink), Regenerative 0…65VDC to 0…1500VDC, 20kW up to 1.5 MW 

• cell system nominal voltage and type of chemistry
• number of cells
• internal resistance and associated parameters
• cell temperature progression
• allowed current
• charge efficiency
• energy computing and management facilities
• time-dependent and functional dependent parameters

• Setting of operational parameters for each output phase: (frequency, phase, voltage, basic waveform)
• Defining functional blocks enabling a wide variety of modulation capabilities
• Defining, editing and storing of even complex and long test sequences
• Preview window for output voltage waveforms
• LC load mode, definition of complex equivalent circuits
• Hand drawing curve tool and FOURIER tool (harmonics synthesis)
• TC.ACS provides an extensive safety concept in order to detect unwanted or off-limit conditions very quickly and to initiate controlled limiting or even a shutdown.

• compact and completely modular design
• high effectiveness in all operation modes, few requirements on building infrastructure
• ability to use an existing liquid cooling system directly
• optional matched liquid-to-air cooling unit TC.LAE available
• possibility of upgrading to systems of up to 1 MVA
• high level of system dynamics, ≤ 5 kHz modulation bandwidth
• non-restrictive capability of refeeding in the Q4 operation mode
• possibility of operating as an autonomous 4-Q and 3-phase quasi-analogue amplifier
• possibility of “Hardware-in-the loop”-operation (HIL mode)
• user friendly application software with pre-configured test patterns
• possibility of integrating into a complete SAS simulation and test system
• galvanic isolation available as an option without derating the simulator port data

Photovoltaic applications, the quality and technical data of the AC-DC converter is of primary interest. Solar installations are intended for a lifetime of roughly 20 years, therefore even fractions of a percent in efficiency will represent significant amounts of energy losses.

Programmable Grid-tie Sink High-Power DC Supply,

Programmable Grid-tie Source & Sink Technology
Wide range of power 20 to 512 kW, expandable up to several MW
DC output voltages from 0-65 VDC up to 0-1500 VDC, +/- 40 A up to +/- 600 A

Rugged, 4-Port, High-Powered USB Hub

• Ultra low noise for optimal performance of audio and video recording equipment
• Durable cast-aluminum housing suitable for the most rugged environments
• Oversized power source guaranteed to support current intensive USB peripherals on all 4 ports simultaneously
• DVM probe port access for monitoring USB device load current on port 1
• AC/DC wall adapter and USB host cable provided

1 – 12 GHz Programmable Phase Shifters

• USB powered and controlled

• Includes easy to install and use GUI

• 360 degree phase control in 1 degree increments

• Calibrated performance for optimal accuracy

• Phase profile upload capability

• API DLL and example programs included

Data Sheets

DC – 20 GHz Programmable Digital Attenuators

• Input power to 2 Watts

• USB powered and controlled

• Includes easy to install and use GUI

• Programmable attenuation ramp

• Operate multiple devices directly from a PC or self powered USB hub

• Easily programmable for ATE applications

Data Sheets

0.5-20 GHz, High Performance Programmable Signal Generators

. USB powered and controlled

• Includes easy to install and use GUI

• Fast switching to 20 GHz

• Selectable internal/external 10 MHz reference

• Phase continuous frequency sweep (LFM)

• High-speed internal and external pulse modulation

• Autonomous operation from USB hub or battery pack

• Robust aluminum construction

• API DLL and LabVIEW compatible drivers available