HIOKI E E CORPORATION

The Memory HiCorder MR8870 is a compact, high-speed data acquisition recorder designed for waveform observation and RMS variation recording in maintenance and fault analysis applications.

Key Features

• Dual recording mode for instantaneous waveforms and RMS variations
• Two isolated analog channels with 2 MW internal memory
• Real-time saving of measured values to CF card
• Synchronize two instruments to record four channels at once
• High-speed performance up to 1 MS per second
• Compact handheld design for easy field transport
• Sharp QVGA TFT wide LCD for clear waveform viewing
• Ideal for elevator, motor, inverter, and machine diagnostics

The Memory HiCorder MR8875 is a high-speed, portable data acquisition recorder designed for vehicle testing, performance evaluation, and advanced multichannel measurements.

Key Features

• 1000 V direct input with instantaneous DC and RMS measurement
• Up to 16 to 60 channels with plug-and-play input modules
• High-speed simultaneous logging down to 2 microseconds
• Real-time recording directly to SD card for long-term logging
• 16-bit high-resolution measurement for accurate results
• Direct CAN bus input for onboard vehicle analysis
• Built-in FFT and waveform calculation for advanced analysis
• Intuitive touch screen interface for fast setup and operation
• Designed to withstand vibration and extreme temperatures

The Memory HiCorder MR8880 is a rugged, field-ready waveform recorder designed to capture high- and low-voltage signals safely in industrial and maintenance applications.

Key Features

• Direct 600 V input for three-phase power measurements
• CAT III 600 V isolation for safe high-voltage testing
• Four completely isolated analog channels
• Simultaneous recording of three-phase systems plus one spare channel
• Wide operating temperature range from minus 10 to 50 degrees Celsius
• Shock- and vibration-resistant housing with side protectors
• Built-in trigger and pre-trigger functions for precise event capture
• Presets function for fast and consistent setup

The Pulse Generator MR8791 is a plug-and-play input module for Hioki Memory HiCorders, designed for precise control simulation testing of electronic control systems.

Key Features

• Outputs pulse and pattern waveforms on up to eight channels
• Supports TTL level and open-collector output signals
• Designed for control simulation testing of ECUs and control boards
• Suitable for engine, airbag, brake, and power steering systems
• Wide frequency range for pulse and logic pattern generation
• Built-in self-test function for reliable operation
• Isolated design between unit and output channels
• Compact form factor for laboratory and test bench integration

The VIR Generator U8794 is a high-precision signal generation unit designed to simulate sensor outputs for ECU inspection, component testing, and maintenance applications.

Key Features

• Generates DC voltage, DC current, and resistance simulation signals
• Ideal for ECU inspection, electronic component testing, and equipment maintenance
• Eight fully isolated output channels for safe multi-signal simulation
• High-accuracy resistance simulation with automatic current calculation
• Designed exclusively for use with Memory HiCorder MR8740 series
• Supports sensor simulation testing without physical sensors
• Compact and lightweight design for bench and field environments

The Waveform Generator U8793 is a plug-and-play module for Hioki Memory HiCorders that enables arbitrary waveform output and anomaly simulation for advanced testing scenarios.

Key Features

• Outputs arbitrary waveform signals on up to two channels
• Reproduces waveforms recorded with a Memory HiCorder up to 15 V
• Generates customized arbitrary waveforms up to 15 V output
• Built-in function generator and sweep function
• Isolated design between unit and outputs and between channels
• Supports anomaly simulation and scenario-based testing
• Includes Waveform Maker software for easy waveform creation
• Designed for use with compatible Hioki Memory HiCorder models

Quantify composite layer resistance and interface resistance in Li-ion battery electrode sheets

The RM2610 Electrode Resistance Measurement System is an advanced tool designed for precise quantification of composite layer resistivity and interface resistance in Li-ion battery electrode sheets. Using cutting-edge inverse problem analysis, the system isolates and calculates resistance values critical for optimizing battery performance. Its intuitive design includes a constant current source and a multi-probe setup, enabling rapid measurements and detailed analysis.

With the ability to measure resistance variations caused by material properties, composition, and manufacturing conditions, the RM2610 accelerates the development of high-performance batteries. This system supports both positive and negative electrodes and provides visual insights into uniformity and density effects. Ideal for research and manufacturing environments, the RM2610 ensures reliable, accurate measurements essential for advancing lithium-ion battery technology.

Rapid 6.4ms Super Megohm and Low Current Testing

Key Features

• 300 times better noise resistance
• Max. 1000 V output: SM7110
• Max. 2 × 10^19 Ω display
• Min. 0.1 fA resolution
• Built-in EXT I/O, RS-232C, GP-IB and USB
• Flexible, Multipurpose Design, High Resistance
• Meter/Electrometer/Picoammeter/IR Meter
• Measure resistance of materials by combining with optional electrode