Products

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +12 to -12 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510 MCOR12 Power Modules are identical and interchangeable.
• Has two high-precision measurements of output current;
  • one is used to close the regulation control loop,
  • provides an independent monitoring signal to the Crate Interface Card.
• Fault sensing circuitry in the module sets a Fault Latch which inhibits the output.
• A (momentary) Sync input signal inhibits MOSFET switching when it is active (high);
  • this eliminate switching noise .
  • reduces power line noise during sensitive analog signal measurements.

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +30 to -30 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510R30 MCOR30 Power Modules are identical and interchangeable
  • Programming Card is plugged into the replacement module.
• Each channel has a critically-damped, LC noise filter with a cut-off frequency of about 8 kHz.
• A 16-pin front panel diagnostics connector taps onto major circuit nodes which enables quick “inthe-crate” fault evaluation

• 2U Chassis – 19″ rack mount 3.48” Height, 9.60” Depth and Weight 6lb.
• Power 120V AC 60Hz
• Washable front removable air filter
• Ball Bearing AC fans provide 330 CFM
• Dual plenum design
• Cooling for 160mm,220mm depth modules
• Diverts lower warmed air to rear of Cabinet
• RM option diverts lower air to front of Cabinet

• accommodate these control schemes
• total control system interface on a single VME-standard card
• occupies the left-most slot of the crate
• monitoring voltage reference inputs, output voltages and fault conditions
• standard VMEbus-compatible 6U by 220 mm board installed
• Eurocard crate
• Two 96-pin I/O connectors

MCOR Modules

MCOR 2/6/9/12

Each module can be customized to provide maximum outputs of 2 amps, 6 amps, 9 amps, and 12 amps. Up to 16 of these can fit in a single 6U VME style crate.

MCOR 30

Each module can provide a maximum output 30 amps. Up to 8 of these can fit in a single 6U VME style crate.

The Hi-Techniques FreeStyle series of Data Acquisition Systems is a versatile, capable solution for mobile and rugged data acquisition applications. FreeStyle was designed from the ground up to make data acquisition as fast and as easy as possible. Just grab your FreeStyle and your computer and head out to the test site.

Flexibility by Design

The Hi-Techniques Synergy series of Data Acquisition Systems integrates superior transient and streaming capability with optimized time and frequency domain performance. Add in universal signal conditioning, real-time math and you’ll see why Synergy is the ultimate Data Acquisition System for all of your mechanical, electrical, acoustic, shock and vibration measurements.

• Independent High Resolution Digitizers
• Up to 1 MS/s per Channel Streaming
• Remote Control, Display and Storage
• Mix and Match Input Modules
• Multiple Instrument Synchronization
• Unparalleled Analysis Capability
• Over 100 Built-in Analysis Functions
• Full Custom Analysis Capability

The Hi-Techniques Synergy series of Data Acquisition Systems integrates superior transient and streaming capability with optimized time and frequency domain performance. Add in universal signal conditioning, real-time math and you’ll see why Synergy is the ultimate Data Acquisition System for all of your mechanical, electrical, acoustic, shock and vibration measurements.

• provides precision bi-polar output currents
• minimal zero-cross over distortion
• 19” rack mounted 6U x 220 mm crate
• crate has 17 slots; 16 (slot 0 thru 15)
• connectors
  • J1 (ExtIntlk),
  • J2 (CrateOK),
  • J3 (Input Reference Voltages),
  • J4 (Output Monitors), and
  • J9 (Bitbus)

Positional current probe,  PCB track Touch & Measure

Unique technology enabling current measurement in PCB tracks bandwidth of DC to 5MHz, dynamic range of 10mA to 20A pk-pk useable with any normal oscilloscope, safety rated to 300V Cat II,  investigates waveforms in any conductor including ground planes.

Bench/System DC Power Supplies, PowerFlex or PowerFlex+ regulated Single or Dual Outputs 1200 watts, with/without Digital Remote Interfaces

• Single or dual outputs, 1200 watts total
• PowerFlex design gives variable voltage/current combinations within a power envelope
• Up to 60 volts or 80 volts and up to 50 amps
• Setting by direct numeric entry or by spin wheel
• High setting resolution of 1mV in up to 60 volts
• Low noise of < 3mV rms at full power
• Bench or rack mounting, front and rear terminals
• Quasi analogue remote control
• RS232, USB GPIB & LAN interfaces (P models)

Bench/System DC Power Supply, PowerFlex Regulation, Smart Analog Controls Single or Dual Outputs, 360 to 840 watts, with/without Remote Interfaces

• PowerFlex design gives variable voltage and current combinations within a maximum power range
• Up to 60 volts and up to 20 amps
• 180 watts or 420 watts maximum per output
• Isolated outputs can be wired in series or parallel
• Constant voltage or constant current operation
• Settings Locking (S-Lock)
• PowerFlex or fixed-range operation
• Variable OVP trips
• Selectable remote sense terminals
• Compact quarter or half rack 3U case size
• Isolated analogue remote control (CPX400SA only)
• RS232, USB, GPIB & LXI compliant LAN (P models only)

Bench/System DC Power Supply, Multi-Range, Digital Control Triple Outputs, 315 or 378W with/without Remote Interfaces

• Three high performance outputs each with full functionality
• Range switching gives variable voltage/current combinations
• Shared power mode provides double power from a single output
• Low output noise and ripple via linear final regulation
• High setting resolution of up to 1mV and 0.1mA
• Variable OVP and OCP trips on all outputs
• 50 setting memories per output plus 50 linked memories
• Selectable voltage tracking (isolated tracking)
• Selectable current meter averaging
• Switchable remote sense capability
• Graphic LCD provides simultaneous output metering
• Numeric or spin-wheel control of all parameters
• Individual or combined output on/off control with
• programmable delay sequencing.
• 3U half-rack case for bench or rack mounting
• GPIB, RS-232, USB and LAN (LXI) interfaces (-P models)
• Duplicate power & sense terminals at rear (-P models)

MX100T and MX100TP:

• 315 watts total power
• Three outputs of equal power, each capable of 35V at 3A
• Range switching provides up to 70 volts and up to 6 amps

MX180T and MX180TP:

• 375 watts plus of total power
• Two high power outputs plus one low power output
• High power outputs each capable of 30 volts at 6 amps
• Range switching provides up to 120 volts or up to 20 amps
• Low power output provides up to 12 volts or up to 3 amps

Bench/System DC Power Supply, Single Output, Mixed-mode Regulation up to 360 watts, with/without remote interfaces

• Compact & lightweight power supply
• 0 to 18V at 0 to 20A or 0 to 35V at 0 to 10A
• Bench or rack mounting, front & rear terminals
• Very low noise, excellent transient response
• Comprehensive protection including OVP trip
• High setting resolution, remote sense terminals
• Analogue controls

P versions add:

• RS-232 and GPIB interfaces as standard
• Keyboard setting of all parameters
• Rotary and delta (step) control of V and I
• Watts display, non-volatile storage of 25 settings
• Fully programmable with bus readback of V & I

Bench/System High Precision DC Power Supply, Linear Regulation, Digital Control Single or Triple Outputs, 105 to 242 watts, with/without Remote Interfaces

• Advanced dc power supplies, single or triple output
• Up to 112 watts per output
• Very high precision, very low noise, excellent dynamics
• Advanced user interface with numeric and rotary control
• Multiple voltage/current ranges for increased flexibility
• Multiple non-volatile memories for power supply set-ups
• Switchable remote sense provides perfect load regulation
• Comprehensive protection including OVP and OCP trips
• Compact bench footprint; modular width for rack mounting
• Auxiliary output fully variable 1.00V to 6.00V at 3A with selectable voltage and current metering (T models)
• Bus programmable via USB, RS232, GPIB or LAN (P models)
• LAN interface is LXI compliant
• Duplicate power and sense terminals at rear (P models)