• High voltage output to 300Vp-p (±150V)
• Output current to 100 mA per channel
• Full power bandwidth from DC to >500kHz
• Slew rate to 200V/µs
• Low distortion
• Low cost
• Custom Configuration of: Gain, Signal Ground

• 12GHz RF Analog Signal Generator
• Extremely fast switching speed of <100μs
• AM, FM, PM Sweep & Pulse Modulation
• Extra small, compact module platform
• Exceptionally Low Phase Noise of -145dBc/Hz @100MHz and 10@kHz offset
• SPI and micro-USB integrated interfaces
• Remotely programmable via MATLAB, Python, LabVIEW
• and other software programming environments.
• Flixible modular platform for OEM and custom requirements
• and applications, to satisfy specific customer demands.
• Multi instrument synchronization capability

• 3 GHz RF Analog Signal Generator
• Extremely fast switching speed of <100μs
• AM, FM, PM Sweep & Pulse Modulation
• Extra small, compact module platform
• Exceptionally Low Phase Noise of -145dBc/Hz @100MHz and 10@kHz offset
• SPI and micro-USB integrated interfaces
• Remotely programmable via MATLAB, Python, LabVIEW
• and other software programming environments.
• Flixible modular platform for OEM and custom requirements
• and applications, to satisfy specific customer demands.
• Multi instrument synchronization capability

• 6GHz RF Analog Signal Generator
• Extremely fast switching speed of <100μs
• AM, FM, PM Sweep & Pulse Modulation
• Extra small, compact module platform
• Exceptionally Low Phase Noise of -145dBc/Hz @100MHz and 10@kHz offset
• SPI and micro-USB integrated interfaces
• Remotely programmable via MATLAB, Python, LabVIEW
• and other software programming environments.
• Flixible modular platform for OEM and custom requirements
• and applications, to satisfy specific customer demands.
• Multi instrument synchronization capability

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +12 to -12 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510 MCOR12 Power Modules are identical and interchangeable.
• Has two high-precision measurements of output current;
  • one is used to close the regulation control loop,
  • provides an independent monitoring signal to the Crate Interface Card.
• Fault sensing circuitry in the module sets a Fault Latch which inhibits the output.
• A (momentary) Sync input signal inhibits MOSFET switching when it is active (high);
  • this eliminate switching noise .
  • reduces power line noise during sensitive analog signal measurements.

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +30 to -30 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510R30 MCOR30 Power Modules are identical and interchangeable
  • Programming Card is plugged into the replacement module.
• Each channel has a critically-damped, LC noise filter with a cut-off frequency of about 8 kHz.
• A 16-pin front panel diagnostics connector taps onto major circuit nodes which enables quick “inthe-crate” fault evaluation

• 2U Chassis – 19″ rack mount 3.48” Height, 9.60” Depth and Weight 6lb.
• Power 120V AC 60Hz
• Washable front removable air filter
• Ball Bearing AC fans provide 330 CFM
• Dual plenum design
• Cooling for 160mm,220mm depth modules
• Diverts lower warmed air to rear of Cabinet
• RM option diverts lower air to front of Cabinet

• accommodate these control schemes
• total control system interface on a single VME-standard card
• occupies the left-most slot of the crate
• monitoring voltage reference inputs, output voltages and fault conditions
• standard VMEbus-compatible 6U by 220 mm board installed
• Eurocard crate
• Two 96-pin I/O connectors

MCOR Modules

MCOR 2/6/9/12

Each module can be customized to provide maximum outputs of 2 amps, 6 amps, 9 amps, and 12 amps. Up to 16 of these can fit in a single 6U VME style crate.

MCOR 30

Each module can provide a maximum output 30 amps. Up to 8 of these can fit in a single 6U VME style crate.

• provides precision bi-polar output currents
• minimal zero-cross over distortion
• 19” rack mounted 6U x 220 mm crate
• crate has 17 slots; 16 (slot 0 thru 15)
• connectors
  • J1 (ExtIntlk),
  • J2 (CrateOK),
  • J3 (Input Reference Voltages),
  • J4 (Output Monitors), and
  • J9 (Bitbus)

• 12GHz RF analog signal generator
• AM, FM, PM, Sweep & Pulse Modulation
• Exceptionally Low Phase Noise of -145dBc/Hz @100MHz and 10@kHz offset
• Field ready, with 10” touch screen suited for day and night use and 2 hour battery operation
• Remotely programmable via MATLAB, Python, LabVIEW and other software programming environments.
• Removable uSD card for instrument security

• 6GHz RF analog signal generator
• AM, FM, PM, Sweep & Pulse Modulation
• Exceptionally Low Phase Noise of -145dBc/Hz @100MHz and 10@kHz offset
• Field ready, with 10” touch screen suited for day and night use and 2 hour battery operation
• Remotely programmable via MATLAB, Python, LabVIEW and other software programming environments.
• Removable uSD card for instrument security

Rugged, 4-Port, High-Powered USB Hub

• Ultra low noise for optimal performance of audio and video recording equipment
• Durable cast-aluminum housing suitable for the most rugged environments
• Oversized power source guaranteed to support current intensive USB peripherals on all 4 ports simultaneously
• DVM probe port access for monitoring USB device load current on port 1
• AC/DC wall adapter and USB host cable provided

1 – 12 GHz Programmable Phase Shifters

• USB powered and controlled

• Includes easy to install and use GUI

• 360 degree phase control in 1 degree increments

• Calibrated performance for optimal accuracy

• Phase profile upload capability

• API DLL and example programs included

Data Sheets

DC – 20 GHz Programmable Digital Attenuators

• Input power to 2 Watts

• USB powered and controlled

• Includes easy to install and use GUI

• Programmable attenuation ramp

• Operate multiple devices directly from a PC or self powered USB hub

• Easily programmable for ATE applications

Data Sheets

0.5-20 GHz, High Performance Programmable Signal Generators

. USB powered and controlled

• Includes easy to install and use GUI

• Fast switching to 20 GHz

• Selectable internal/external 10 MHz reference

• Phase continuous frequency sweep (LFM)

• High-speed internal and external pulse modulation

• Autonomous operation from USB hub or battery pack

• Robust aluminum construction

• API DLL and LabVIEW compatible drivers available