Products

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +12 to -12 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510 MCOR12 Power Modules are identical and interchangeable.
• Has two high-precision measurements of output current;
  • one is used to close the regulation control loop,
  • provides an independent monitoring signal to the Crate Interface Card.
• Fault sensing circuitry in the module sets a Fault Latch which inhibits the output.
• A (momentary) Sync input signal inhibits MOSFET switching when it is active (high);
  • this eliminate switching noise .
  • reduces power line noise during sensitive analog signal measurements.

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +30 to -30 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510R30 MCOR30 Power Modules are identical and interchangeable
  • Programming Card is plugged into the replacement module.
• Each channel has a critically-damped, LC noise filter with a cut-off frequency of about 8 kHz.
• A 16-pin front panel diagnostics connector taps onto major circuit nodes which enables quick “inthe-crate” fault evaluation

• 2U Chassis – 19″ rack mount 3.48” Height, 9.60” Depth and Weight 6lb.
• Power 120V AC 60Hz
• Washable front removable air filter
• Ball Bearing AC fans provide 330 CFM
• Dual plenum design
• Cooling for 160mm,220mm depth modules
• Diverts lower warmed air to rear of Cabinet
• RM option diverts lower air to front of Cabinet

• accommodate these control schemes
• total control system interface on a single VME-standard card
• occupies the left-most slot of the crate
• monitoring voltage reference inputs, output voltages and fault conditions
• standard VMEbus-compatible 6U by 220 mm board installed
• Eurocard crate
• Two 96-pin I/O connectors

MCOR Modules

MCOR 2/6/9/12

Each module can be customized to provide maximum outputs of 2 amps, 6 amps, 9 amps, and 12 amps. Up to 16 of these can fit in a single 6U VME style crate.

MCOR 30

Each module can provide a maximum output 30 amps. Up to 8 of these can fit in a single 6U VME style crate.

• provides precision bi-polar output currents
• minimal zero-cross over distortion
• 19” rack mounted 6U x 220 mm crate
• crate has 17 slots; 16 (slot 0 thru 15)
• connectors
  • J1 (ExtIntlk),
  • J2 (CrateOK),
  • J3 (Input Reference Voltages),
  • J4 (Output Monitors), and
  • J9 (Bitbus)

• 16K Video Generator & Analyzer
• Dolby Vision™, HDR 10 and HDR 10+
• validating DP 1.4a & DP 2.0 Link Layer on DP Sinks and Sources
• Power Input +12 Vdc (AC/DC converter included)
• Module Size/Weight TBD for Weight and Size

• Compact sized DisplayPort™ 1.2 compliant Reference Sink
• HBR2 and MST capable Sink and Branch device
• Cerified as the platform for DP 1.2 LL CTS Ext1 tests
• Optional MST Debug panel and AUX Channel Monitor
• Debug and Test Controller GUI enables monitoring and previewing any MST stream
• User programmable EDID and DPCD

•  HDMI 2.1 Test Equipment (FRL)
• Enhanced Gaming Features (VRR, ALLM)
• FEC, Forward Error Correction
• HDCP 2.2 & HDCP 2.3 support  TMDS Support
• Dolby Vision™ Test Tool
• 8K@60 fps Support (12 Gbps/channel)
• eARC Support (end of 2019)
• DSC Support (ESTIMATED 2020)
• UCD Console GUI for debugging
• High level API for easy integreation

• Automated tests for USB-C™ DisplayPort™ Alt Mode
• Electrical Test to verify whole USB-C connector with single cable insert
• Test USB 2.0 and USB 3.0
• 4K@60 support
• Easily set test parameters with provided Software
• Easily run tests from the commandline
• Unigraf’s Test System Interface (TSI) Support
• Third Part Test Management Software
• Support e.g. NI TestStand Support

• UHD / 4K compliant test equipment
• HDMI 2.0 and DP 1.2 input and output in one unit
• DCP Approved HDCP 2.3 CTS Test Tool
• HDCP 1.3 and HDCP 2.3 support
• Sink and source video, audio and configuration parameters
• USB 3.0 connected
• UCD Console GUI for debugging
• High level API for easy integration

• Test DP over USB-C video and audio
• Test USB-C Power Delivery with DP Alt Mode
• DCP Apporved HDCP 2.3 CTS Tests
• Verify interface signal continuity
• 4K@60 support
• HDCP 1.3 and HDCP 2.3 support
• Capture video and audio, monitor and control interface parameters
• USB signal pass-thru
• UCD Console GUI for debugging
• High level API for easy integration

• VESA Certified DP 1.4 Link Layer CTS Test Tool
• DCP Approved HDCP 2.3 CTS Tool
• 8K and 4K Reference Sink, Source & Repeater
• DP 1.4 / HBR3 input and output in one unit
• USB-C input and output with supplied converter cable
• MST support (4 streams)
• DSC Sink, FEC and LTTPR support
• HDCP 1.3 and HDCP 2.3 support
• High level API for easy integration

USB-C DisplayPort Alt Mode Test Unit DP 1.4a, HBR3 & PD 3.0

• 8K and 4K Reference Sink & Source
• DP 1.4a Link Layer CTS for Sinks & Sources
• HDCP 2.3 CTS for Transmitters & Receivers
• DP 1.4a features:
  * Up to HBR3 simultaneous input and output in one unit
  * DSC Sink & Source with off-line encoding and decoding
  * FEC and LTTPR support
  * MST support (4 streams)
• USB-C v1.3 with Power Delivery 3.0
  * DP Alt Mode
  * Capable to sink & source 9V@3A
  * PD Role swaps supported
• USB3.2Gen2 (10Gbit/s) bypass between test interfaces
• HDCP 1.3 and HDCP 2.3 support