News

Aim-TTi QPX Series Bench/System DC Power Supply with PowerFlex or PowerFlex+ regulation, Single or Dual Outputs up to 1200 watts, with/without Digital Remote Interfaces

QPX series laboratory power supplies are designed to provide flexibility in the choice of voltage and current so as to meet multiple diverse applications. Voltages up to 80V and currents up to 50A are available within a defined power envelope.

Unlike most power supplies of this power level, the QPX series is well suited to bench top applications in addition to system use.

POWERFLEX & POWERFLEX+

A conventional PSU has a fixed current limit giving a power capability that reduces directly with the output voltage. The Aim-TTi PowerFlex and PowerFlex+ regulation systems enable higher currents to be generated at lower voltages within an overall power limit envelope.

For PowerFlex+ models the output can provide more than six times the current of a conventional PSU of the same maximum voltage and power. For PowerFlex models the increase is three times

LOW RIPPLE AND NOISE

PowerFlex and PowerFlex+ use either a balanced multi-phase converter system or linear final regulation to minimise ripple and improve dynamic performance. This provides unusually low noise for thepower level coupled with good transient response

CURRENT METER AVERAGING

When measuring rapidly varying loads it can become difficult to get accurate readings from the current meter. By selecting meter averaging, the reading is stabilised by averaging the last four readings to reduce the speed and extent of the variation.

OVP AND OCP TRIPS

Variable trips for over-voltage and overcurrent are provided on each output. Unlike a limit setting, the trip setting turns the output off and provides a different level of protection.

For example, when repetitively testing a unit which normally takes a peak current of 10A, the current limit could be set to 11A and the OCP to 10.1A to ensure that a faulty unit will trip the supply off and not be damaged by over dissipation. The output trip can also be activated by other fault conditions including over temperature and remote sense mis-wiring. The cause of the trip is shown on the display. Learn more by downloading the datasheet

Aim-TTi QPX Series Datasheet AIM-QPX_SERIES_Data_Sheet-Issue_1

Up to 80V or 50A per output limited by power curve Low ripple and noise of <3mV rms at full power High setting resolution and metering down to 1mV Analog control interface, LAN/LXI, USB, RS232† & GPIB* on P versions Bench or System use with rear and front terminals*

Aim-TTi QPX Series

Bench/System Multi-Range DC Power Supply with digital control, 3 or 4 Outputs, 315 to 420W with/without Remote Interfaces

The MX series uses mixed mode regulation to provide up to 420W of power split across up to four outputs, this series differs from most other multi-output power supplies in offering full capabilities on all outputs. Each output features CV or CI operation, simultaneous high resolution metering, switchable remote sensing, OVP and OCP trips, and an individual output switch. To increase its ability to match the widest range of applications, each output has more than one range giving the choice of higher voltage or higher current.

When higher power is required, up to two outputs can be disabled to provide twice the power from one or two outputs – up to 210 watts for the MX100T/MX100Q and up to 360 watts for the MX180T

Aim-TTi MX SERIES

TMetrix is proud to announce that we have partnered with K&S Advanced Systems to distribute their products in Canada. K&S Advanced Systems develops and manufactures systems that set the next-level industry standard of vibration isolation for precision instruments. Their dedication to system design stems from their long history with scientific instruments. As engineers, physicists and industry consultants, they have developed, installed and worked with active and passive vibration cancellation systems, giving them a great understanding of their benefits—and their current limitations.

Corporate Goal

K&S Advanced Systems’ goal is to become a world-leader in the design and manufacture of HI technologically innovative vibration isolation systems, solutions for vibration sensitive instruments, tools and processes.

Industries

High precision tools are sensitive to vibrations and require vibration isolation for optimal performance.

Main functionalities

Products

Soto TT

Soto TT are lightweight, compact tabletop passive vibration isolation systems that allow for a significant reduction in unwanted vibrations translated to working environment from various environmental disturbances.

Key features

• Highly dampened step response
• Simple installation that requires not tuning
• Application-specific designs
• Capabilities to meet your needs
• Ability to support massive machines, tools and systems

Aris TT

Aris TT are lightweight, compact tabletop active vibration isolation systems that counteract unwanted vibrations for sensitive equipment. Their streamlined design allows them to seamlessly become part of the workstation environment and their straightforward composition requires no follow-up tuning.

Key features

• 6 degrees of freedom
• Active gain starting from 0.5Hz
• Variable damping (patent pending)
• Built-in artificial intelligence feature
• Adjustable by software active bandwidth
• Remote control
• Built-in real-time diagnostic tools
• Spectrum analyzer
• Oscilloscope
• Shaker mode

Aris MD

Aris MD are lightweight, compact tabletop active vibration isolation systems that counteract unwanted vibrations for sensitive equipment. Their streamlined design allows them to seamlessly become part of the workstation environment and their straightforward composition requires no follow-up tuning.

Key features

• 6 degrees of freedom
• Active gain starting from 0.5Hz
• Variable damping (patent pending)
• Built-in artificial intelligence feature
• Adjustable by software active bandwidth
• Remote control
• Built-in real-time diagnostic tools
• Spectrum analyzer
• Oscilloscope
• Shaker mode

Soto MD

Soto MD are lightweight, compact vibration absorption systems that allow for a significant reduction in unwanted vibrations translated to working environment from various environment disturbances.

Key features

• Highly dampened step response
• Simple installation that requires not tuning
• Application-specific designs
• Capabilities to meet your needs
• Ability to support massive machines, tools and systems

Learn More

Click here to learn more about K&S and their distinctive products.

K&S Advanced Systems

Do you perform EMC tests in a reverberation chamber?

THIS FREE NEXIO – WEBINAR IS FOR YOU:
“A tour of reverb tests”
Reverb tests on 5 continents with BAT-EMC since 2007!

2 sessions on Tuesday June 29:
– Central European Time – from 11am to 11:45am
– Eastern Standard Time (New York) – from 11am to 11:45am

You are invited to participate in the NEXIO products webinar (english version). On this occasion, we will introduce you to the BAT-EMC test automation software. The webinar will be on GoToWebinar, in live and free by registration.

NEXIO – WEBINAR “A tour of reverb tests”

About Tabor Electronics

Benchtop powerhouse

The 7234 is a benchtop powerhouse. With its exclusive DC max topology it is able to deliver an amazing 28 amps of continuous DC power into the EUT—almost double what was previously possible. The DC max technology also increases the 7234’s ability to sync current by an impressive 50%. When coupled with AE Techron’s 3110A standards waveform generator, it creates a compact, very competent conducted immunity test system.

Value proposition

The 7234 is configurable, multi-mode and scalable. A key to the 7234’s value proposition is its configurability. The 7234 has a slew rate in excess of 100 volts per microsecond, making it the fastest battery simulator available. It is able to accurately produce dropouts and surges, with rise and fall times as short as 1.2 microseconds, meeting present test requirements with capacity left for customer-requested over-testing or future more stringent standards.

Battery simulator to amplifier

With the flip of a couple of switches, the 7234 is able to go from being a low-voltage, high-current battery simulator to a wide bandwidth DC blocked amplifier, ideal for driving coupling transformers in aviation standards like DO160, Section 18 and 19, or automotive standards like ISO11452-10.

Fast slew rate

One problem inherent in wide-bandwidth coupling transformers, like those used in EMC test standards, is the reduced output for a given input voltage at higher frequencies. This reduced output requires the amplifier to produce greater voltages to achieve the desired voltage out of the coupling transformer. The fast slew rate of the 7234 allows it to produce higher voltages at higher frequencies than other similar products.

Driving loads

Circuit topology of the 7234 was initially developed for, and is used to this day, to drive very inductive loads, like MRI gradient coils in some pretty interesting locations. This designed-in ability to drive highly inductive loads, coupled with a voltage potential of up to 150 volts peak, make it an ideal amplifier for driving loads like radiating loops or Helmholtz coils that are highly inductive.

Portability

The 7234 is small, rugged and efficient. At less than 50 pounds in weight and 2U in height, the amplifier is small enough and light enough to be easily moved from one test location to another. There are times when the object to be measured is too large to be moved. The 7234 is mechanically rugged enough to use in the field if needed. Even if the physical environment in your lab is less hostile than those encountered outdoors, it is very likely that the loads that need to be driven are not. Because of this AE Techron has made the 7234 just as tough electrically. AE Techron has combined a robust design with comprehensive, conservatively set protections and finished with resettable circuits and breakers instead of fuses. This makes missed connections, output shorts and system ground loops, events that could mean an extended stay at the repair shop for lesser products, a simple turn off the power, fix the issue and start again for the AE Techron.

Compelling warranty

For the small chance that the 7234 might be damaged, AE Techron has a three-year, no-fault warranty and a 30-day repair turnaround guarantee. The hidden cost of ownership of other products at this power level is a requirement for three-phase power. The 7234 is efficient enough that it can be powered from a standard single-phase wall outlet, avoiding the expense of running special power to the test location.

Another area where the 7234 can save a great deal of money is in its scalability. When there is that one test that requires just a little bit more than is available from a single 7234, instead of purchasing a new larger system, simply flip a switch, connect a second 7234 in parallel and resume testing.

In summary

More DC power.
Faster slew rate.
More voltage potential.
Ability to source and sink.
Compact, efficient, rugged.
Field configurable.
Scalable.
3-year no-fault warranty.

The 7234 represents an unbeatable value.

In October 2020 Form Factor completed the acquisition of Boulder, Colorado-based High Precision Devices, Inc. (HPD), a respected supplier of scientific instruments, especially precision cryogenic instruments. The transaction makes HPD part of FormFactor, bolstering FormFactor’s capabilities, capacity, portfolio of products—and potential. Exciting times for FormFactor as the HPD approach is to work with top-flight researchers, engineers and scientific organizations to provide practical solutions from concept to fruition. HPD is imaginative, connected and knows how to deliver.

The key to any corporate acquisition is whether or not the product lines, services and cultures of the two companies are a good match. FormFactor’s acquisition of HPD is a great fit as HPD’s impressive range of precision cryogenic instruments, including chip-scale cryogenic probe systems and cryostats capable of extremely low temperatures, beautifully complement Form Factor’s existing line of cryogenic wafer probe systems and cryogenic engineering probes, expanding its market reach with cryostats for die and package testing and lower-temperature wafer probe capabilities.

Small, rectangular ADR cryostat

HPD cryostats provide an alternative to more expensive and space consuming dilution refrigerators (DR). These Adiabatic Demagnetization Refrigerators (ADR) are great for applications that do not need the full power of a DR, but still require sub-Kelvin temperatures. HPD’s ADRs provide a faster, compact, and less costly path to temperatures a fraction of a degree above absolute zero. And the new Continuous ADRs (CADR) allow the cold to be maintained.

Leveraging the strength and scale of HPD and FormFactor together, a broad portfolio of ultra-low temperature test technologies can now be offered to enable scientific and industrial customers to tackle important societal challenges, solutions to which will benefit people  around the world for generations to come. One such need that HPD/FormFactor are staring down is solving the data center energy crisis, solutions to which will contribute to the mitigation of climate change. Another need is realizing the astonishing possibilities of quantum computing, which is now being oriented toward real-world use in pharmaceutical, data security and other applications. Quantum computing, along with superconducting computing, are now experiencing tremendous growth and will likely have profound impacts on various emerging technologies and, ultimately, in our everyday lives. HPD’s technical team brings highly specialized skills and know-how to address the unique test challenges for these emerging technologies.

Cryogenic circuitry could revolutionize computing

Long before these technologies mentioned above become reality, years of development is required for many of the essential components. Conceptualization, prototyping, and refinement of these superconducting devices can only be performed at cryogenic temperatures. HPD 4 K cryogenic probe stations and millikelvin Adiabatic Demagnetization Refrigerator (ADR)  research cryostats serve a vital role in many of these endeavors. As a result, through its acquisition of HPD, FormFactor has positioned itself to be an important player in the development of a host of forward-looking technologies that will improve quality of life in the decades ahead.