News

TDK Lambda’s SFL DC Electronic Load Series was developed to provide an electronic load for the design, evaluation and manufacture of regulated DC power supplies, fuel cells, solar cells, batteries and components. Sales of the series commenced in July 2020.

Key features of the SFL DC Electronic Load Series

• The SFL series is multi-functional, programmable and offers power levels of 300W (3U half rack) and 1000W (3U full rack) with high-speed response and stable operation at low voltage. The series also offers seven load operating modes that allow the user to connect and test products under various operating conditions.
• There are two different dynamic operating modes: Dynamic Frequency Mode (allows the user to switch the load between two different settings for a single pulse or repeating pulse profile); and Dynamic Time Mode (allows the user to program up to 16 load settings that can be programmed for a repeating pulse profile). Both modes also provide a rear panel TRIG OUT function for waveform scope viewing or for synchronization with other test equipment.
• A Sequence function is built-in where simple/complex waveforms can be created (up to 1024 time steps) using Excel-based control software and digital interface communication (USB or IEEE). A Sweep Mode feature is also available, allowing for product testing where devices/products require test sweeps in CR mode for V-I characteristic testing, CC mode for overcurrent protection characteristic testing or CP for overpower protection characteristic testing.
• The SFL series has a V Mode function that automatically changes the load mode (when voltage is rising or falling) or turns off the load input until the load voltage reaches a set value, on-board memory for storage/recall of up to eight operational settings and a rear panel Remote Sense selection switch and connection ports for connection and voltage measurement across the test device.
• Model functions can be set up via the 3.5” color LCD front panel display (which has oscilloscope-like function keys on the vertical and horizontal borders). Using these keys in combination with the four embedded operating allows for adjustment, setup, storage and recall of the load operating parameters. These model functions are also accessible via the built-in USB interface or the optional IEEE Interface.
• Higher power DC load systems (up to 10kW) are achievable using a Master-Slave unit arrangement and a simple parallel cable connection from unit-to-unit, with all system control and monitoring performed through the master unit (for easy interfacing).
• Multi-channel synchronous operation (with triggering) is also available and allows multiple DC electronic loads to be connected to separate devices by using the same parallel cable connection from unit-to-unit. Synchronized load ON/OFF and Dynamic operation are featured in a Master-Slave configuration with up to ten units (up to 10kW total).
• Optional interfaces offered include the IEEE Interface (with a built-in DIDO Interface) and the Ripple Measurement Module (R ) Interface. The IEEE Interface is 488.1 compliant with instrument software drivers available for use. The DIDO  Interface allows for remote interfacing with PLC controllers and includes isolated control and status of load ON/OFF, Range setting, Alarm Detection/Clear and Sweep Function Pass/Fail status.
• Models are available in 300W and 1000W power levels with Output voltages of 120V (60A and 180A) and 500V (18A and 36A) and are powered from a universal single-phase AC input (85~264VAC, 47~63Hz).

About TKD-Lambda

TDK-Lambda Corporation, a subsidiary of TDK Corporation, is a global supplier and recognized leader of power conversion products suited to many applications, including: medical, industrial, broadcast, defense, factory automation and LED/LCD signage. With global sales in excess of $500 million, they have design, manufacturing, and sales locations in Japan, China, EMEA, ASEAN, and the Americas. TDK-Lambda’s view is a “Power Supply” is more than just an electronic device. It is the “heart” of their customers’ systems and the core element of safety and reliability.

What is an electric field probe?

An electric field (E-field) probe is a long, spherical probe-capped wand that detects unsafe levels of RF emissions and gives operators data on the electric field in an area. E-field probes are also used in anechoic chambers (rooms that completely absorb reflections of sound or electromagnetic waves), OATS locations (open air test sites) as well as other unique applications, such as monitoring emissions of aerospace and military systems. An E-field probe generally consists of a dipole antenna, readout device, RF detector and non-perturbing transmission line.

The FL8000 Series—a “3-in-1” solution

Launched in spring 2021, AR’s FL8000 Series of five E-field probes is a new generation of field probes that offer a “3-in-1” solution—the capability of measuring, with a single probe:

• Continuous-wave electric fields;
• Pulsed electric fields; and
• Modulated electric fields.

Covering the 5 kHz – 60 GHz frequency range, this “3-in-1” solution represents the ultimate in E-field probe versatility for simplifying EMC testing in the lab. In the past this testing often required multiple field probes for measuring different types of electric fields in commercial, automotive, military, and aviation applications. This compromised lab layout and efficiency.

As AR CEO John Kim notes:

“We continue to raise the bar in probe testing functionality and integration to help our customers improve the layout and efficiency of their testing labs. With the unique combination of the wide frequency ranges, unmatched reliability, and multiple measurement types, the FL8000 Series is the single go-to solution for meeting a variety of EMC standards.”

The FL8000 series offers exceptional linearity and dynamic range performance to enable the accuracy required for even the most demanding testing. With fiber power connectivity, the FL8000 Series provides an easy migration path, all while delivering the reliability that has made AR the world leader in field monitoring.

FL8000 Series kits

The Field Probe kits contain a laser probe interface, and everything needed to operate its associated field probe.

FL8000 series highlights

• Separable-axis field probe capable of measuring continuous-wave, pulsed and modulated electric fields
• Use of laser to deliver power-over-fiber allows for continuous operation without recharging or replacing batteries
• Correction factors from accredited ISO 17025 lab

About AR

Founded in 1969 and located in Souderton, Pennsylvania, Amplifier Research (AR) does business as AR RF/Microwave Instrumentation. The company is a leading supplier of RF/microwave benchtop and rack-mounted broadband, high-powered, solid-state RF and microwave amplifiers, antennas, amplifier modules, complete EMC test systems, EMI receivers, military communications booster amplifiers and more. AR has developed a strong customer base in a wide range of markets including communications, military, commercial, wireless, medical, automotive, aerospace, product compliance testing, research and education.

Maintaining lead acid batteries for UPS stations requires the measurement of dozens to hundreds of cells, introducing potential human recording errors and time-consuming data management. Preventing the need to redo measurements and efficiently manage location data can help save time and increase efficiency. Hioki’s latest portable battery tester, BT3554-52, an update of the BT3554-50, helps streamline UPS and lead acid battery diagnostics with high-precision measurements and voice-guided capability.

BT3554-52 features

The Battery Tester BT3554-52 Pro Kit comes with new features that will help streamline measurements by providing operators the ability to input location information as well as applications-based audio guidance for measurement sequence and results.

About Hioki

Established in 1935, Hioki has grown to become a world leader in providing consistent delivery of test and measuring instruments through advanced design, manufacturing, sales and service. Click here for more information.

Battery Tester BT3554-52 Pro Kit

Based in Rorschach, Switzerland, Regatron AG has over 45 years of experience in electronics manufacturing and is known for its high-quality modular power supplies. Regatron thus fully appreciates the demands of working with high-power batteries and understands how essential it is to:

• Monitor voltages, currents and temperatures and to keep them within a safe range; and
• Pay close attention to polarity and voltage levels when connecting a battery to a load or battery tester.

Previously, batteries were relatively simple cell stacks. That certainly is not the case today. Batteries are now complex modules with superposed power electronics that require highly accurate data acquisition and fast response times.

What does the G5.BT battery tester series do?

Regatron’s G5.BT Battery Tester Series represents the latest development stage of the company’s DC power supplies. The series was developed in order to test energy storage devices and, in doing so, to meet the requirements outlined above. Some of the technology and exceptional features of the series that helps achieve the goals that inspired the series are outlined below:

• Technologically advanced, fast switching, compact 19-inch power supplies
• Current accuracy of <0.02% FS, additional high-resolution current measurement range
• Voltage accuracy of 0.01% FS
• Current rise time in the 50…200 µs range – even at higher power levels
• Detection of reverse polarity connection
• Overcurrent protection in case of unmatched voltages between battery and tester
• Current ripple modulation up to 10 kHz
• Wide current-voltage range with an auto-ranging factor of 3
• CV, CC, CP, CR, and Ri-Sim control modes
• Power regeneration and a high degree of efficiency

Why you should purchase the G5.BT battery tester series

Ensuring that personnel are safe and equipment is protected is vital. The G5.BT series, therefore, includes the field-proven RPP feature that guards against the two main risk factors that come into play when a battery is physically connected to the battery tester:

1) RPP reliably prevents all serious damage caused by accidental reverse polarity between battery and battery tester.

2) RPP provides overcurrent protection/soft start in case of unmatched voltages between the battery and the battery test system. Another valuable function of the integrated RPP feature is the prevention of deep battery discharge at ‘Voltage Off’ state.

The G5.BT series is modular and features easy scalable systems. The modularity of the series allows it to be easily adapted to ever-changing test requirements. Not only is it possible to reconfigure between parallel, series, and mixed operation, but also to expand the system with additional power supply units or to split it into smaller units. In addition, the G5.BT series features power regeneration and a high degree of efficiency, resulting in significant reduction of energy consumption and heat dissipation. The purchase of a G5.BT Regatron battery tester is thus a solid investment that continues to deliver benefits over the long term.

Applications

The G5.BT Battery Tester Series is bidirectional regenerative and best suited for battery module/pack-testing in laboratory or test bench environments. The excellent current and voltage accuracy, the fast current rise time, and the powerful integrated CAN multi-protocol interface enable tests with a high temporal and electrical resolution. The specialized application software BatControl allows the user to set many test parameter values and even to define complex test procedures. Therefore, the versatile G5.BT series can be used for testing all types of batteries and energy storage systems.

Contact

Click here to learn more about Regatron’s New G5.BT Battery Tester Series or to request a quote.

Regatron’s New G5.BT Battery Tester Series

Aim–TTi is one of the world’s major producers of laboratory power supplies (PSUs). It has been a major technology innovator in PSUs since 1979 and offers products ranging from 30 watts up to 1200 watts. Hundreds of thousands of Aim-TTi power supplies are in everyday use around the world, a testament to the company’s strength and resolve in both research and development and production.

QPX Series: PowerFlex power supplies

The one word that comes to mind when assessing the attributes of the QPX series of power supplies is “flexibility”—at a level well beyond that of conventional laboratory power supplies. This flexibility opens the door to new opportunities for today’s engineers and translates to tremendous value for their companies, year after year.

A conventional PSU has a fixed current limit giving a power capability that drops off directly with the output voltage. With the Aim-TTi PowerFlex design, QPX power supplies make it possible to generate higher currents at lower voltages within an overall power limit envelope. It does this through use of a modified form of mixed-mode regulation. PowerFlex+ uses a multi-phase conversion technique to eliminate the need for a linear final stage and offers an even wider range of voltage/current combinations. QPX power supplies are ideal for both bench-top and system applications with front and rear terminals and a wide range of interfaces. They can, therefore, perform the task of many different power supplies, reducing the need for investment in other units. Indeed, flexibility is the operative word with the QPX series.

QPX series models also have 4 digit V/I meters and an analog end control, resulting in low noise and wrinkle levels.

The QPX series provides options for labs of all kinds. The QPX1200S & SP offer a current capability of 20 amps at the maximum output of 60 volts, and the PowerFlex design offers increased output current with reduced output voltage. The QPX600D & DP offer 1200 watts of maximum power, arranged as two isolated outputs of 600 watts each with PowerFlex+, offering a much wider flexing range of more than 61⁄2:1. The QPX600D can be operated as two entirely independent power supplies, each with its own display. Alternatively, multiple tracking modes are available including series and parallel operation which provide metering of total voltage or total current respectively.

News: new PowerFlex+ 750W DC laboratory power supply

In addition to the above models, Aim-TTi is proud to offer its new PowerFlex+ 750W DC laboratory power supply— the QPX750SP. The latest addition to the QPX series, the QPX750SP is a single output 750W unit housed in a compact 3U half rack width case with front ventilation and low noise fan assisted cooling. Front and rear power and sense terminals make it equally at home on the bench or in a rack.  The RM460 4U rack kit (available separately) houses one or two QPX750SPs with ½U rack spacing above and below providing full ventilation.

PowerFlex+ regulation means that the QPX750SP is capable of voltages of up to 80V and currents up to 50A within a 750W power envelope. A balanced multi-phase converter system minimizes ripple and improves dynamic performance. This provides unusually low noise for the power level, coupled with good transient response.

A comprehensive array of interfaces including USB, LAN/LXI and quasi-analogue are standard. GPIB is available as a factory or customer fit option. The QPX750SP is compatible with Aim-TTi Test Bridge software, providing graphical remote instrument control, logging and sequencing.

Contact

Click here to learn more about Aim-TTi’s QPX series of power supplies or to request a quote.

Aim-TTi’s QPX Series Bench / System DC Power Supplies

Brent Gibbs joins the ACA TMetrix Inc. family Brent is a seasoned sales professional and Electrical Technologist with more than 20 years of experience working with customers across Western Canada. His understanding of industrial process, control and automation, predictive maintenance technologies and test and measurement systems make him an asset to any business. NEW! G5 RSS Programmable Regenerative DC Power Supplies A new generation! The new G5.RSS series features high control dynamics, an exceptional accuracy, a nominal output voltage of up to 3000 VDC, and a wide current-voltage range with an auto-ranging factor of 3 geared to get the best value! READ MORE Regenerative Grid Simulators REGATRON’s 3-in-1 full 4-Quadrant, Regenerative, Bidirectional Source & Sink Grid Simulators (Grid Simulator, Power Amplifier and AC load)‎ of the series TC.ACS are of a precisely engineered, high quality, modular design. READ MORE TESLA 200 With next generation test capabilities, anti-arcing solutions, wafer automation, and support for both engineering probes and production probe cards, the TESLA200 now enables complete thermal testing (-55°C to 300 °C) with fully-automatic thinned/warped/TAIKO wafer loading. One system covers all on-wafer high power test needs, from R&D to niche production. Visit our website   UPCOMING WEBINAR Unigraf, a leading provider of test tools for video electronics manufacturers and ACA TMetrix Inc. will be hosting an in-depth technical webinar on innovations and milestones in the industry for HDMI, DisplayPort and USB-C in 2021. Watch for upcoming details. GENESYS+ SERIES Utilizing embedded microprocessor technology to provide advanced performance and functionality, the GENESYS+™ series has the highest power density and lightest weight available for its size with a comprehensive set of user-friendly interfaces. Visit our website

December 2020 Newsletter

TC.ACS is a series of full-digital, full-4-quadrant, 3-phase AC power sources. Each TC.ACS unit in the series has exceptional programming features and represents a three-in-one configuration:

• Versatile synthesized 3-phase grid simulator with four fully controlled active outputs.
• Built-in full 4-quadrant 1 to 3-phase power amplifier with three independent and galvanic isolated amplifier inputs.
• Programmable RLC-load mode (electronic AC load with grid recuperation) to substitute for real and bulky resistors, inductors and capacitors.

The multi-level inverter technology opens up a wide base frequency range from DC up to 1000Hz—and an exceptionally high modulation bandwidth of 5 kHz. This allows for the exact reproduction of harmonic distortion up to the 100th harmonic @ 50 Hz or the 83th harmonic @ 60Hz. The system can be easily adapted to tasks in R+D, the laboratory, end-of-line testing and education.

TC.ACS applications

With the application software ACSControl, the user can program:

• Variation of basic system voltages and frequency
• Settings of phase relationship
• Voltage drops in the whole network or individual drops per phase
• Micro ruptures and flickers
• Over- and under voltages
• Voltage asymmetries
• Superimposed harmonic and interharmonic voltage waveforms
• Variation of phase angles
• Special conditions for EMC testing
• Transition from feeding to recuperation operation and vice versa
• Analyses of energy flow

Hardware

The modular structure based on 30 kVA or 50 kVA units allows for a flexible adaptation to the customer’s power requirements. Systems of up to 1000kVA can be set up by simply connecting basic units in a parallel mode. The hardware operates in all four quadrants and can fully refed into the power system. The system also enables testing power feedback units and operation of linear and nonlinear feeding systems for measuring and evaluation purposes. Operation in single phase mode is also possible down to DC mode.

User Software ACSControl

The tailor-made software tool ACSControl allows the operator either to:

• Manually operate the system, or;
• Program and run automated test sequences and to use the functionality of data acquisition of the system.

• Compact and completely modular design
• High effectivity in all operation modes
• Can use an existing liquid cooling system directly
• Optional matched liquid-to-air cooling unit TC.LAE available
• Possibility of upgrading to systems of up to 1 MVA
• High level of system dynamics, ≤ 5 kHz modulation bandwidth
• Non-restrictive capability of refeeding in the Q4 operation mode
• Possibility of operating as an autonomous 4-Q and 3-phase quasi-analogue amplifier
• Possibility of “Hardware-in-the loop”-operation (HIL mode)
• User friendly application software with pre-configured test patterns
• Possibility of integrating into a complete SAS simulation and test system
• Galvanic isolation available as an option without derating the simulator port data
• Three different operation modes:
  a) Programmable Grid Simulator
  b) Remote operated 4Q AC voltage amplifier
  c) Electronic AC-load featuring programmable RLC load impedance

TC.ACS Grid Simulators made by Regatron AG can, for example, be operated as a self-contained system for comprehensive testing of solar and additive energy inverters. In the field of power test and development labs the high degree of programmability allows all imaginable grid situations and evaluation procedures to be established.

TC.ACS is the ideal tool for all R&D and simulation work.