Research, University & Colleges

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +12 to -12 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510 MCOR12 Power Modules are identical and interchangeable.
• Has two high-precision measurements of output current;
  • one is used to close the regulation control loop,
  • provides an independent monitoring signal to the Crate Interface Card.
• Fault sensing circuitry in the module sets a Fault Latch which inhibits the output.
• A (momentary) Sync input signal inhibits MOSFET switching when it is active (high);
  • this eliminate switching noise .
  • reduces power line noise during sensitive analog signal measurements.

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +30 to -30 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510R30 MCOR30 Power Modules are identical and interchangeable
  • Programming Card is plugged into the replacement module.
• Each channel has a critically-damped, LC noise filter with a cut-off frequency of about 8 kHz.
• A 16-pin front panel diagnostics connector taps onto major circuit nodes which enables quick “inthe-crate” fault evaluation

• Wide AC Input Voltage range for three-phase 208VAC, 400VAC and 480VAC Input.
• High Power Factor (0.88 for Vout < 600V; 0.93 for Vout > 600V).
• Built-In Protective functions (OVP, UVL, FOLD, OTP, AC-FAIL).
• Output Isolation to 600V for Vout < 600V; to 1500V for Vout > 600V.
• High Efficiency ( > 77% for Vout < 30V, > 88% for 30V < Vout < 600V, > 93.5% for Vout > 600V).
• Rack-mount with provision for chassis slides; Zero-stacking for maximum power density.
• Cooling Fan speed control (for reduced audible noise and longer life): Vout > 30V.
• Light weight: < 97lbs (43kg) for Vout < 600V / < 70lbs (32kg) for Vout > 600V.
• Dimensions: 5.25”/133mm: Height-3U x 19.00”/483mm: Width x 22.85”/581mm: Length
• Fast Up/Down Programming Response Time (100ms/50ms for Vout < 600V, 17ms / 20ms for Vout > 600V).

The VirtuaLUN provides full control and programmability of Fibre Channel parameters, allocating unique storage test conditions for SAN testing and development.

SANBlaze VirtuaLUN storage emulation for FCoE is the key piece of test equipment for anyone developing products supporting the FCoE storage protocol. The VirtuaLUN feature set provides a unique set of functions applicable in all aspects of a product life cycle: from development to design validation and test and QA.

3-Channel AC/DC Power Meter for Single-Phase to 3P4W Equipment such as Motors, Inverters, Power Conditioners, and Power Supplies.

Programmable Grid-tie Source & Sink Technology
Wide range of power 20 to 512 kW, expandable up to several MW
DC output voltages from 0-65 VDC up to 0-1500 VDC, +/- 40 A up to +/- 600 A

CT100HF, stainless-steel SMA test port

• Higher-bandwidth version of the CT100S featuring the fastest TDR system risetime, ideal for testing high-frequency cables and interconnects with resolution and precision previously restricted to unwieldly bench-top TDR instruments.

CT100 TDR ONLINE USER GUIDE 

CT100 AUTOMATED METALLIC TDR CABLE TESTER FEATURES 

CT VIEWER™ TDR SOFTWARE, FOR USE WITH CT100 SERIES TDRS

CT100S, stainless-steel SMA test port

• CT100 TDR configured with SMA test port assembly. Represents a balance of performance and electrical overstress protection for field applications where SMA test port is desired.

CT100 TDR ONLINE USER GUIDE 

CT100 AUTOMATED METALLIC TDR CABLE TESTER FEATURES 

CT VIEWER™ TDR SOFTWARE, FOR USE WITH CT100 SERIES TDRS

CT100, self-grounding BNC test port

• Electrically-rugged, multipurpose metallic TDR designed for high-resolution testing of a wide range of coaxial and twisted-pair cable types and lengths — in the field, on the manufacturing floor, or in the lab. Exceeds all Tektronix® 1502C TDR specifications.

CT100 TDR ONLINE USER GUIDE 

CT100 AUTOMATED METALLIC TDR CABLE TESTER FEATURES 

CT VIEWER™ TDR SOFTWARE, FOR USE WITH CT100 SERIES TDRS

DC, 0.5 Hz To 1 MHz, 6-Channel 3-Phase 4-Wire Power Meter with Direct and Clamp Sensor Input

3-Phase 4-Wire Portable Power Quality Analyzer to Detect, Measure and Record Power Quality Issues, Harmonics, Demand, Inrush and Power Transients

3-Phase 4-Wire Power Quality Analyzer Compliant to IEC61000-4-30 Class A Standards with Dynamic 1300V Range, Harmonic and Inter-harmonics Analysis Capabilities

3 mΩ to 3000 Ω/60V DC Battery Testers for Production Line Testing of Battery Packs and Modules

Battery Testers for Lithium-ion Battery Evaluation

7-1/2 Digit, 20ppm High Precision DC Voltmeter for Lithium-ion Batteries

7-1/2 Digit, 9ppm High Precision DC Voltmeter for Lithium-ion Batteries

Wide Range 100 mΩ to 100 MΩ DC Resistance Meter with Low Power Resistance Mode for Testing Chip Inductors and EMC Suppression Components on Production Lines

Wide Range 3 mΩ to 3 MΩ Portable DC Resistance Meter with 0.1 μΩ Resolution for Equipment Maintenance and Quality Control