Products

The AZX Series (Regenerative AC / DC Power Source) is a family of high power, single, split and three phase, AC, DC and AC+DC output capable Power Sources with full energy recovery to the AC mains when sinking power from the equipment under test. Available models range from 30 kVA to 440 kVA. Using a modern color touch screen based user interface for ease of use, the AZX Series is cost effective and fully programmable for both basic frequency conversion and advanced AC power line or DC power disturbance test applications requiring up to 1000 Hz fundamental frequency.

The energy recovery capability allows both sourcing and sinking of current and power up to 100% of rated power. Adding the Load Option (Option L) adds full electronic regenerative AC & DC Load programming capability to the AZX.

• High-Speed Current Control: No dynamic overshoot or oscillation
• High Slew-Rate: Up to 30A/*s for fast load changes
• Low Voltage Operation: Stable operation with no turn-on delay
• Multi-Functional: Seven load modes and four operating modes
• Parallel Operation: Up to 10kW with 10 units
• User-Friendly Interface: Built-in USB and optional IEEE interfaces
• Compliance: EN61010-1 compliant with a two-year warranty

• S-parameters DC to 40 GHz, single-ended and mixed-mode
• Impedance Profile with <1 mm resolution, differential and common-mode
• Internal, automatic OSLT calibration
• USB-connected, small, lightweight
• Flexible display of the measurements
• Remove effects from fixtures, connectors and cables
• Emulate eye diagrams with CTLE, DFE and FFE equalization
• Advanced jitter analysis

The new G5.RSS series features

• High control dynamics
• An exceptional accuracy
• A nominal output voltage of up to 3000 VDC
• A wide current-voltage range with an auto-ranging factor of 3.
• You get the best value for your investment.

• The S type Channel card provides economical, high-performance power measurement with a basic 0.1% accuracy and enough bandwidth to handle waveforms up to 1.25 MHz.
• The A-type ultra-precision Channel card offers a 2-year accuracy rating of 0.03% of reading and bandwidth up to 1.25 MHz.
• The W type Wideband Channel card performs precision power measurements on the toughest real-world waveforms, with sampling speed fast enough to tame waveforms up to 5Mhz

• High Power Accuracy of 0.045% For All Channels
• Improved Voltage and Current Self-Heating Adders
• Faster Sampling Rates & Bandwidth Performance
• Greater Harmonic Frequencies

• Ultra High Power Accuracy of 0.024% For All Channels
• Improved Voltage and Current Self-Heating Adders
• Faster Sampling Rates & Bandwidth Performance
• Greater Harmonic Frequencies

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +12 to -12 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510 MCOR12 Power Modules are identical and interchangeable.
• Has two high-precision measurements of output current;
  • one is used to close the regulation control loop,
  • provides an independent monitoring signal to the Crate Interface Card.
• Fault sensing circuitry in the module sets a Fault Latch which inhibits the output.
• A (momentary) Sync input signal inhibits MOSFET switching when it is active (high);
  • this eliminate switching noise .
  • reduces power line noise during sensitive analog signal measurements.

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +30 to -30 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510R30 MCOR30 Power Modules are identical and interchangeable
  • Programming Card is plugged into the replacement module.
• Each channel has a critically-damped, LC noise filter with a cut-off frequency of about 8 kHz.
• A 16-pin front panel diagnostics connector taps onto major circuit nodes which enables quick “inthe-crate” fault evaluation

High‐Resolution Portable TDR with Frequency‐Domain Analysis Tools

Ideal for testing all types of microwave/RF and digital cables and connectors

• Rugged portable TDR with S‐parameter tools
• Resolves connector detail (<1 cm)
• 75 μm (0.003 in.) cursor resolution
• 16‐bit digital sampling at up to 250 KSPS
• Stores thousands of TDR traces
• USB host/client, 10/100 Ethernet
• Lightweight, bright color screen
• Internet streaming and remote control

Simplify Aging Aircraft Wiring Maintenance Using High-Resolution MOHR CT100 Series TDR Cable Analyzers

• Designed for use with the high-resolution CT100 TDR Cable Tester
• Ideal for TDR testing MIL-STD-1553B data bus aerospace cable assemblies
• Detect and localize open, short, and partial cable and connector faults on the main bus and stubs
• Detects cable and connector faults through 3+ transformer couplers
• Simplifies troubleshooting of aging aircraft MIL-STD-1553 cable assemblies

Photovoltaic applications, the quality and technical data of the AC-DC converter is of primary interest. Solar installations are intended for a lifetime of roughly 20 years, therefore even fractions of a percent in efficiency will represent significant amounts of energy losses.

Programmable Grid-tie Sink High-Power DC Supply,

Programmable Grid-tie Source & Sink Technology
Wide range of power 20 to 512 kW, expandable up to several MW
DC output voltages from 0-65 VDC up to 0-1500 VDC, +/- 40 A up to +/- 600 A