Products

Key Features Provide Application Versatility

• USB, LAN (LXI), IEEE-488.2 and RS-232C with SCPI compatibility
• Compatible with PPSC Studio graphical user interface
• LabVIEW for Windows®/LabWindows® drivers
• Waveform Creation by Harmonic Synthesis
• Waveform Capture (Voltage and Current)
• Harmonic Analysis (Voltage and Current)
• Metering of RMS and Peak Values
• Continuous Self Calibration (CSC)
• Line Sync
• 6:1 Peak Current Capability
• Low Impedance for EN61000-3-2, 3 Testing
• Programmable Output Impedance
• Up to 0-300 VAC Direct Coupled Out
• 1 Phase / 3 Phase Switch Selectable
• 15-5000 Hz Full Power Bandwidth
• Power Levels from 500 VA to 6 kVA standard; 30kVA optional
• Externally Referenced Meter Calibration
• CE Safety & EMC and NTRL Safety Mark

• Advanced semiconductor technology
• High-quality construction
• Rapid capacitor and pulse-forming network charging
• Compact and lightweight design
• Simple parallel operation for higher power needs
• Compatible with worldwide input voltages and frequencies
• Fully adjustable output voltage
• Comprehensive remote control interface

The AZX Series (Regenerative AC / DC Power Source) is a family of high power, single, split and three phase, AC, DC and AC+DC output capable Power Sources with full energy recovery to the AC mains when sinking power from the equipment under test. Available models range from 30 kVA to 440 kVA. Using a modern color touch screen based user interface for ease of use, the AZX Series is cost effective and fully programmable for both basic frequency conversion and advanced AC power line or DC power disturbance test applications requiring up to 1000 Hz fundamental frequency.

The energy recovery capability allows both sourcing and sinking of current and power up to 100% of rated power. Adding the Load Option (Option L) adds full electronic regenerative AC & DC Load programming capability to the AZX.

• High-Speed Current Control: No dynamic overshoot or oscillation
• High Slew-Rate: Up to 30A/*s for fast load changes
• Low Voltage Operation: Stable operation with no turn-on delay
• Multi-Functional: Seven load modes and four operating modes
• Parallel Operation: Up to 10kW with 10 units
• User-Friendly Interface: Built-in USB and optional IEEE interfaces
• Compliance: EN61010-1 compliant with a two-year warranty

The new G5.RSS series features

• High control dynamics
• An exceptional accuracy
• A nominal output voltage of up to 3000 VDC
• A wide current-voltage range with an auto-ranging factor of 3.
• You get the best value for your investment.

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +12 to -12 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510 MCOR12 Power Modules are identical and interchangeable.
• Has two high-precision measurements of output current;
  • one is used to close the regulation control loop,
  • provides an independent monitoring signal to the Crate Interface Card.
• Fault sensing circuitry in the module sets a Fault Latch which inhibits the output.
• A (momentary) Sync input signal inhibits MOSFET switching when it is active (high);
  • this eliminate switching noise .
  • reduces power line noise during sensitive analog signal measurements.

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +30 to -30 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510R30 MCOR30 Power Modules are identical and interchangeable
  • Programming Card is plugged into the replacement module.
• Each channel has a critically-damped, LC noise filter with a cut-off frequency of about 8 kHz.
• A 16-pin front panel diagnostics connector taps onto major circuit nodes which enables quick “inthe-crate” fault evaluation

Photovoltaic applications, the quality and technical data of the AC-DC converter is of primary interest. Solar installations are intended for a lifetime of roughly 20 years, therefore even fractions of a percent in efficiency will represent significant amounts of energy losses.

Programmable Grid-tie Sink High-Power DC Supply,

Programmable Grid-tie Source & Sink Technology
Wide range of power 20 to 512 kW, expandable up to several MW
DC output voltages from 0-65 VDC up to 0-1500 VDC, +/- 40 A up to +/- 600 A

AC Flexible Clamp Sensors in 3 Diameter Sizes

Power supply for the Clamp on AC/DC sensors unit

DC to 15 kHz/2000A AC/DC Clamp On Current Probe

DC to 20 kHz/200A AC/DC Clamp On Current Probe

DC to 10 kHz/100A AC/DC Clamp On Current Probe

Power Supply Unit for Outputting Current Probe Signals to Memory HiCorders and Oscilloscopes