Products

A high-purity 20MHz DDS function generator designed for engineers requiring precision signal output, advanced modulation, and digital control.

Key Features:

• Frequency range: 0.001Hz to 20MHz
• High resolution: 6 digits or 1mHz
• Excellent stability (1ppm) and 10ppm one-year accuracy
• Digital control for phase-continuous sweep (linear or logarithmic)
• Output range: 5mV to 20V peak-to-peak from 50 or 600 Ohms
• Low distortion sine wave with high spectral purity
• Built-in modulation: AM, FSK, gated mode, tone switching
• Store and recall multiple instrument setups
• USB and RS232 interfaces for remote control

A high-performance 20MHz DDS function generator offering precise waveform control, high spectral purity, and flexible remote interfacing.

Key Features:

• Frequency range: 0.001Hz to 20MHz
• High resolution: 6 digits or 1mHz
• Frequency stability: ±1ppm, accuracy: ±10ppm
• Ultra-low distortion sine waves with high spectral purity
• Internal linear/log sweep with phase continuity
• Built-in AM, FSK, gated, and tone-switching modes
• Output: 5mV to 20V pk-pk from 50Ω or 600Ω
• Store and recall multiple instrument set-ups
• USB and RS232 interfaces for remote programming

High-performance dual-channel function and arbitrary waveform generator with up to 240 MHz output for advanced test and signal needs.

Key Features:

• Frequency range from 40 MHz to 240 MHz
• Dual independent or coupled full-performance channels
• Precise phase control: 0.001° resolution
• Arbitrary waveform support up to 800 MS/s
• Replay rates up to 80 MHz
• Wide range of built-in and user-defined waveforms
• Pulse generation up to 100 MHz, low jitter
• Internal/external modulation, sweep, gated, and burst modes
• USB, LAN (LXI compliant), and optional GPIB
• PC software for waveform generation and editing

Key Features:

• Single output up to 360W: Choose between 18V/20A or 35V/10A
• Mixed-mode regulation for high accuracy and low noise
• Fanless convection cooling for completely silent operation
• Bench or rack mountable, front and rear terminals
• OVP trip, high-resolution settings, and remote sense terminals
• P models offer USB, RS232, LAN interfaces (GPIB optional)
• Rotary, keypad, and step control for voltage and current
• Non-volatile memory for storing up to 25 user presets
• Seamless integration with Test Bridge software and automation systems

Single-phase, 2U, industrial amplifier/battery simulator

• Bench-sized
• Powered from 120V/230VAC
• Source and Sink (4 quadrant)
• Rugged Design
• 3-Year, No-Fault Warranty

Key Performance Capabilities:

• Drop outs and surges as fast as 1.2µs
• Small signal response up to 1 MHz
• 13.5 VDC at up to 28A
• Field-selectable ±40V, 75V or 150V potential

Key Performance Capabilities:

• Slew rates up to 60 V/µsec.
• Up to 240A DC at +50VDC or –50VDC (4301-240 configuration).
• Can provide pulses of up to 800 amps at voltages of up to ±100V (4301-240 configuration).
• Adjustable compensation allows the system to maintain a 50V/2 µsec rise-time over a wide range of current outputs.

Key Performance Capabilities:

• Bandwidth: DC to 50 kHz
• Voltage: 0 to 250 V_RMS; 0 to 350 VDC
• Current: 100 to 500 A_RMS
• Distortion: 0.1%
• Power: 4 kW to 20 kW*Power levels up to 5X rated power when driving reactive loads
• High power efficiency and density

*Models available with output from 4 kW to 20 kW (capable of up to 125 kVA).

Key Performance Capabilities:

• 4-Quadrant – Can source and sink current
• ±80V – DC supply for 12V to 48V systems; meets 80V surge requirements
• 300 kHz Sine – DC ripple tests for all major standards
• 3µs Rise Time – Exceeds surge and dropout slew rate requirements
• 3mΩ DC Source Impedance – Out-performs ISO 7637-2 requirements
• Supports ground reference and supply offset testing required for ISO 16750-2 Sect. 4.8 and other similar standards

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +12 to -12 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510 MCOR12 Power Modules are identical and interchangeable.
• Has two high-precision measurements of output current;
  • one is used to close the regulation control loop,
  • provides an independent monitoring signal to the Crate Interface Card.
• Fault sensing circuitry in the module sets a Fault Latch which inhibits the output.
• A (momentary) Sync input signal inhibits MOSFET switching when it is active (high);
  • this eliminate switching noise .
  • reduces power line noise during sensitive analog signal measurements.

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +30 to -30 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510R30 MCOR30 Power Modules are identical and interchangeable
  • Programming Card is plugged into the replacement module.
• Each channel has a critically-damped, LC noise filter with a cut-off frequency of about 8 kHz.
• A 16-pin front panel diagnostics connector taps onto major circuit nodes which enables quick “inthe-crate” fault evaluation

• 2U Chassis – 19″ rack mount 3.48” Height, 9.60” Depth and Weight 6lb.
• Power 120V AC 60Hz
• Washable front removable air filter
• Ball Bearing AC fans provide 330 CFM
• Dual plenum design
• Cooling for 160mm,220mm depth modules
• Diverts lower warmed air to rear of Cabinet
• RM option diverts lower air to front of Cabinet

• accommodate these control schemes
• total control system interface on a single VME-standard card
• occupies the left-most slot of the crate
• monitoring voltage reference inputs, output voltages and fault conditions
• standard VMEbus-compatible 6U by 220 mm board installed
• Eurocard crate
• Two 96-pin I/O connectors

MCOR Modules

MCOR 2/6/9/12

Each module can be customized to provide maximum outputs of 2 amps, 6 amps, 9 amps, and 12 amps. Up to 16 of these can fit in a single 6U VME style crate.

MCOR 30

Each module can provide a maximum output 30 amps. Up to 8 of these can fit in a single 6U VME style crate.

The Hi-Techniques FreeStyle series of Data Acquisition Systems is a versatile, capable solution for mobile and rugged data acquisition applications. FreeStyle was designed from the ground up to make data acquisition as fast and as easy as possible. Just grab your FreeStyle and your computer and head out to the test site.

Flexibility by Design

The Hi-Techniques Synergy series of Data Acquisition Systems integrates superior transient and streaming capability with optimized time and frequency domain performance. Add in universal signal conditioning, real-time math and you’ll see why Synergy is the ultimate Data Acquisition System for all of your mechanical, electrical, acoustic, shock and vibration measurements.

• Independent High Resolution Digitizers
• Up to 1 MS/s per Channel Streaming
• Remote Control, Display and Storage
• Mix and Match Input Modules
• Multiple Instrument Synchronization
• Unparalleled Analysis Capability
• Over 100 Built-in Analysis Functions
• Full Custom Analysis Capability