Products

The AZX Series (Regenerative AC / DC Power Source) is a family of high power, single, split and three phase, AC, DC and AC+DC output capable Power Sources with full energy recovery to the AC mains when sinking power from the equipment under test. Available models range from 30 kVA to 440 kVA. Using a modern color touch screen based user interface for ease of use, the AZX Series is cost effective and fully programmable for both basic frequency conversion and advanced AC power line or DC power disturbance test applications requiring up to 1000 Hz fundamental frequency.

The energy recovery capability allows both sourcing and sinking of current and power up to 100% of rated power. Adding the Load Option (Option L) adds full electronic regenerative AC & DC Load programming capability to the AZX.

Key Performance Capabilities:

• Slew rates up to 60 V/µsec.
• Up to 240A DC at +50VDC or –50VDC (4301-240 configuration).
• Can provide pulses of up to 800 amps at voltages of up to ±100V (4301-240 configuration).
• Adjustable compensation allows the system to maintain a 50V/2 µsec rise-time over a wide range of current outputs.

Key Performance Capabilities:

• Bandwidth: DC to 50 kHz
• Voltage: 0 to 250 V_RMS; 0 to 350 VDC
• Current: 100 to 500 A_RMS
• Distortion: 0.1%
• Power: 4 kW to 20 kW*Power levels up to 5X rated power when driving reactive loads
• High power efficiency and density

*Models available with output from 4 kW to 20 kW (capable of up to 125 kVA).

Key Performance Capabilities:

• 4-Quadrant – Can source and sink current
• ±80V – DC supply for 12V to 48V systems; meets 80V surge requirements
• 300 kHz Sine – DC ripple tests for all major standards
• 3µs Rise Time – Exceeds surge and dropout slew rate requirements
• 3mΩ DC Source Impedance – Out-performs ISO 7637-2 requirements
• Supports ground reference and supply offset testing required for ISO 16750-2 Sect. 4.8 and other similar standards

Key Performance Capabilities:

• Up to 900 watts RMS power output (7136 model)
• Small signal response up to 400 kHz
• User-adjustable precision DC offset
• User-adjustable current limit: 1A to 25A
• 4-quadrant operation
• AC/DC coupled

Key Performance Capabilities:

• Up to 900 watts RMS power output (7136 model)
• Small signal response up to 400 kHz
• User-adjustable precision DC offset
• User-adjustable current limit: 1A to 25A
• 4-quadrant operation
• AC/DC coupled

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +12 to -12 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510 MCOR12 Power Modules are identical and interchangeable.
• Has two high-precision measurements of output current;
  • one is used to close the regulation control loop,
  • provides an independent monitoring signal to the Crate Interface Card.
• Fault sensing circuitry in the module sets a Fault Latch which inhibits the output.
• A (momentary) Sync input signal inhibits MOSFET switching when it is active (high);
  • this eliminate switching noise .
  • reduces power line noise during sensitive analog signal measurements.

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +30 to -30 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510R30 MCOR30 Power Modules are identical and interchangeable
  • Programming Card is plugged into the replacement module.
• Each channel has a critically-damped, LC noise filter with a cut-off frequency of about 8 kHz.
• A 16-pin front panel diagnostics connector taps onto major circuit nodes which enables quick “inthe-crate” fault evaluation

• 2U Chassis – 19″ rack mount 3.48” Height, 9.60” Depth and Weight 6lb.
• Power 120V AC 60Hz
• Washable front removable air filter
• Ball Bearing AC fans provide 330 CFM
• Dual plenum design
• Cooling for 160mm,220mm depth modules
• Diverts lower warmed air to rear of Cabinet
• RM option diverts lower air to front of Cabinet

• accommodate these control schemes
• total control system interface on a single VME-standard card
• occupies the left-most slot of the crate
• monitoring voltage reference inputs, output voltages and fault conditions
• standard VMEbus-compatible 6U by 220 mm board installed
• Eurocard crate
• Two 96-pin I/O connectors

MCOR Modules

MCOR 2/6/9/12

Each module can be customized to provide maximum outputs of 2 amps, 6 amps, 9 amps, and 12 amps. Up to 16 of these can fit in a single 6U VME style crate.

MCOR 30

Each module can provide a maximum output 30 amps. Up to 8 of these can fit in a single 6U VME style crate.

• provides precision bi-polar output currents
• minimal zero-cross over distortion
• 19” rack mounted 6U x 220 mm crate
• crate has 17 slots; 16 (slot 0 thru 15)
• connectors
  • J1 (ExtIntlk),
  • J2 (CrateOK),
  • J3 (Input Reference Voltages),
  • J4 (Output Monitors), and
  • J9 (Bitbus)

• 16K Video Generator & Analyzer
• Dolby Vision™, HDR 10 and HDR 10+
• validating DP 1.4a & DP 2.0 Link Layer on DP Sinks and Sources
• Power Input +12 Vdc (AC/DC converter included)
• Module Size/Weight TBD for Weight and Size

• Compact sized DisplayPort™ 1.2 compliant Reference Sink
• HBR2 and MST capable Sink and Branch device
• Cerified as the platform for DP 1.2 LL CTS Ext1 tests
• Optional MST Debug panel and AUX Channel Monitor
• Debug and Test Controller GUI enables monitoring and previewing any MST stream
• User programmable EDID and DPCD

•  HDMI 2.1 Test Equipment (FRL)
• Enhanced Gaming Features (VRR, ALLM)
• FEC, Forward Error Correction
• HDCP 2.2 & HDCP 2.3 support  TMDS Support
• Dolby Vision™ Test Tool
• 8K@60 fps Support (12 Gbps/channel)
• eARC Support (end of 2019)
• DSC Support (ESTIMATED 2020)
• UCD Console GUI for debugging
• High level API for easy integreation

• Automated tests for USB-C™ DisplayPort™ Alt Mode
• Electrical Test to verify whole USB-C connector with single cable insert
• Test USB 2.0 and USB 3.0
• 4K@60 support
• Easily set test parameters with provided Software
• Easily run tests from the commandline
• Unigraf’s Test System Interface (TSI) Support
• Third Part Test Management Software
• Support e.g. NI TestStand Support