The AZX Series (Regenerative AC / DC Power Source) is a family of high power, single, split and three phase, AC, DC and AC+DC output capable Power Sources with full energy recovery to the AC mains when sinking power from the equipment under test. Available models range from 30 kVA to 440 kVA. Using a modern color touch screen based user interface for ease of use, the AZX Series is cost effective and fully programmable for both basic frequency conversion and advanced AC power line or DC power disturbance test applications requiring up to 1000 Hz fundamental frequency.

The energy recovery capability allows both sourcing and sinking of current and power up to 100% of rated power. Adding the Load Option (Option L) adds full electronic regenerative AC & DC Load programming capability to the AZX.

Karis SRK Series Server Cabinets are a reliable way to keep sensitive electronics safe. The professional design features a ventilation rate of more than 74%, providing adequate cooling for the entire system. Karis’s server cabinets will make integrating your data center or data closet fast and easy.

• Curved locking front door with ventilation rate above 80%
• Split locking rear door with ventilation rate above 80%
• Horizontally split locking side panels make access easy
• Two heights, two depths, and two widths available
• Rear vertical cable managers (two) include
• Square hole mounting rails are adjustable front to rear
• Grounding kit included
• Levelers and heavy duty casters come standard
• Full range of optional accessories
• 5 year warranty

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +12 to -12 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510 MCOR12 Power Modules are identical and interchangeable.
• Has two high-precision measurements of output current;
  • one is used to close the regulation control loop,
  • provides an independent monitoring signal to the Crate Interface Card.
• Fault sensing circuitry in the module sets a Fault Latch which inhibits the output.
• A (momentary) Sync input signal inhibits MOSFET switching when it is active (high);
  • this eliminate switching noise .
  • reduces power line noise during sensitive analog signal measurements.

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +30 to -30 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510R30 MCOR30 Power Modules are identical and interchangeable
  • Programming Card is plugged into the replacement module.
• Each channel has a critically-damped, LC noise filter with a cut-off frequency of about 8 kHz.
• A 16-pin front panel diagnostics connector taps onto major circuit nodes which enables quick “inthe-crate” fault evaluation

• 2U Chassis – 19″ rack mount 3.48” Height, 9.60” Depth and Weight 6lb.
• Power 120V AC 60Hz
• Washable front removable air filter
• Ball Bearing AC fans provide 330 CFM
• Dual plenum design
• Cooling for 160mm,220mm depth modules
• Diverts lower warmed air to rear of Cabinet
• RM option diverts lower air to front of Cabinet

• accommodate these control schemes
• total control system interface on a single VME-standard card
• occupies the left-most slot of the crate
• monitoring voltage reference inputs, output voltages and fault conditions
• standard VMEbus-compatible 6U by 220 mm board installed
• Eurocard crate
• Two 96-pin I/O connectors

MCOR Modules

MCOR 2/6/9/12

Each module can be customized to provide maximum outputs of 2 amps, 6 amps, 9 amps, and 12 amps. Up to 16 of these can fit in a single 6U VME style crate.

MCOR 30

Each module can provide a maximum output 30 amps. Up to 8 of these can fit in a single 6U VME style crate.

• provides precision bi-polar output currents
• minimal zero-cross over distortion
• 19” rack mounted 6U x 220 mm crate
• crate has 17 slots; 16 (slot 0 thru 15)
• connectors
  • J1 (ExtIntlk),
  • J2 (CrateOK),
  • J3 (Input Reference Voltages),
  • J4 (Output Monitors), and
  • J9 (Bitbus)

Rugged, 4-Port, High-Powered USB Hub

• Ultra low noise for optimal performance of audio and video recording equipment
• Durable cast-aluminum housing suitable for the most rugged environments
• Oversized power source guaranteed to support current intensive USB peripherals on all 4 ports simultaneously
• DVM probe port access for monitoring USB device load current on port 1
• AC/DC wall adapter and USB host cable provided

1 – 12 GHz Programmable Phase Shifters

• USB powered and controlled

• Includes easy to install and use GUI

• 360 degree phase control in 1 degree increments

• Calibrated performance for optimal accuracy

• Phase profile upload capability

• API DLL and example programs included

Data Sheets

DC – 20 GHz Programmable Digital Attenuators

• Input power to 2 Watts

• USB powered and controlled

• Includes easy to install and use GUI

• Programmable attenuation ramp

• Operate multiple devices directly from a PC or self powered USB hub

• Easily programmable for ATE applications

Data Sheets

0.5-20 GHz, High Performance Programmable Signal Generators

. USB powered and controlled

• Includes easy to install and use GUI

• Fast switching to 20 GHz

• Selectable internal/external 10 MHz reference

• Phase continuous frequency sweep (LFM)

• High-speed internal and external pulse modulation

• Autonomous operation from USB hub or battery pack

• Robust aluminum construction

• API DLL and LabVIEW compatible drivers available

20 MHz to 6 GHz Programmable Signal Generators

• USB powered and controlled
• Includes easy-to-install-and-use GUI
• Programmable frequency stepping
• Operate multiple devices directly from a PC or self-powered USB hub
• Autonomous operation from USB hub or battery pack
• Easily programmable for ATE applications
• Robust aluminum construction
• Customization available for unique requirements
• API DLL and LabVIEW compatible drivers available

Download Data Sheeet

• SPDT and SP4T models available
• 10 Watt power handling capability
• USB powered and controlled
• Includes easy to install and use GUI
• Manual, Internal and External switch control capability
• Operate multiple devices directly from a PC or self powered USB hub
• Easily programmable for ATE applications
• Robust aluminum construction

Data Sheets