• Reliable and Repeatable solid state signal generation
• Standard Internal/external pulse modulation
• USB/Ethernet Control
• 10 MHz external or internal reference
• 100 Hz Frequency Resolution
• Easily portable
• Sized to fit into a single rack unit for ATE applications

• Reliable and Repeatable solid state digital attenuation
• Includes GUI, Windows and Linux SDK, LabVIEW driver
• Programmable attenuation ramp and fading profiles
• Operate multiple devices directly from a PC or self-powered hub
• Easily portable USB powered device
• USB and Ethernet control interfaces

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +12 to -12 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510 MCOR12 Power Modules are identical and interchangeable.
• Has two high-precision measurements of output current;
  • one is used to close the regulation control loop,
  • provides an independent monitoring signal to the Crate Interface Card.
• Fault sensing circuitry in the module sets a Fault Latch which inhibits the output.
• A (momentary) Sync input signal inhibits MOSFET switching when it is active (high);
  • this eliminate switching noise .
  • reduces power line noise during sensitive analog signal measurements.

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +30 to -30 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510R30 MCOR30 Power Modules are identical and interchangeable
  • Programming Card is plugged into the replacement module.
• Each channel has a critically-damped, LC noise filter with a cut-off frequency of about 8 kHz.
• A 16-pin front panel diagnostics connector taps onto major circuit nodes which enables quick “inthe-crate” fault evaluation

• 2U Chassis – 19″ rack mount 3.48” Height, 9.60” Depth and Weight 6lb.
• Power 120V AC 60Hz
• Washable front removable air filter
• Ball Bearing AC fans provide 330 CFM
• Dual plenum design
• Cooling for 160mm,220mm depth modules
• Diverts lower warmed air to rear of Cabinet
• RM option diverts lower air to front of Cabinet

• accommodate these control schemes
• total control system interface on a single VME-standard card
• occupies the left-most slot of the crate
• monitoring voltage reference inputs, output voltages and fault conditions
• standard VMEbus-compatible 6U by 220 mm board installed
• Eurocard crate
• Two 96-pin I/O connectors

MCOR Modules

MCOR 2/6/9/12

Each module can be customized to provide maximum outputs of 2 amps, 6 amps, 9 amps, and 12 amps. Up to 16 of these can fit in a single 6U VME style crate.

MCOR 30

Each module can provide a maximum output 30 amps. Up to 8 of these can fit in a single 6U VME style crate.

• provides precision bi-polar output currents
• minimal zero-cross over distortion
• 19” rack mounted 6U x 220 mm crate
• crate has 17 slots; 16 (slot 0 thru 15)
• connectors
  • J1 (ExtIntlk),
  • J2 (CrateOK),
  • J3 (Input Reference Voltages),
  • J4 (Output Monitors), and
  • J9 (Bitbus)

High‐Resolution Portable TDR with Frequency‐Domain Analysis Tools

Ideal for testing all types of microwave/RF and digital cables and connectors

• Rugged portable TDR with S‐parameter tools
• Resolves connector detail (<1 cm)
• 75 μm (0.003 in.) cursor resolution
• 16‐bit digital sampling at up to 250 KSPS
• Stores thousands of TDR traces
• USB host/client, 10/100 Ethernet
• Lightweight, bright color screen
• Internet streaming and remote control

Simplify Aging Aircraft Wiring Maintenance Using High-Resolution MOHR CT100 Series TDR Cable Analyzers

• Designed for use with the high-resolution CT100 TDR Cable Tester
• Ideal for TDR testing MIL-STD-1553B data bus aerospace cable assemblies
• Detect and localize open, short, and partial cable and connector faults on the main bus and stubs
• Detects cable and connector faults through 3+ transformer couplers
• Simplifies troubleshooting of aging aircraft MIL-STD-1553 cable assemblies

Rugged, 4-Port, High-Powered USB Hub

• Ultra low noise for optimal performance of audio and video recording equipment
• Durable cast-aluminum housing suitable for the most rugged environments
• Oversized power source guaranteed to support current intensive USB peripherals on all 4 ports simultaneously
• DVM probe port access for monitoring USB device load current on port 1
• AC/DC wall adapter and USB host cable provided

1 – 12 GHz Programmable Phase Shifters

• USB powered and controlled

• Includes easy to install and use GUI

• 360 degree phase control in 1 degree increments

• Calibrated performance for optimal accuracy

• Phase profile upload capability

• API DLL and example programs included

Data Sheets

DC – 20 GHz Programmable Digital Attenuators

• Input power to 2 Watts

• USB powered and controlled

• Includes easy to install and use GUI

• Programmable attenuation ramp

• Operate multiple devices directly from a PC or self powered USB hub

• Easily programmable for ATE applications

Data Sheets

0.5-20 GHz, High Performance Programmable Signal Generators

. USB powered and controlled

• Includes easy to install and use GUI

• Fast switching to 20 GHz

• Selectable internal/external 10 MHz reference

• Phase continuous frequency sweep (LFM)

• High-speed internal and external pulse modulation

• Autonomous operation from USB hub or battery pack

• Robust aluminum construction

• API DLL and LabVIEW compatible drivers available

20 MHz to 6 GHz Programmable Signal Generators

• USB powered and controlled
• Includes easy-to-install-and-use GUI
• Programmable frequency stepping
• Operate multiple devices directly from a PC or self-powered USB hub
• Autonomous operation from USB hub or battery pack
• Easily programmable for ATE applications
• Robust aluminum construction
• Customization available for unique requirements
• API DLL and LabVIEW compatible drivers available

Download Data Sheeet

• SPDT and SP4T models available
• 10 Watt power handling capability
• USB powered and controlled
• Includes easy to install and use GUI
• Manual, Internal and External switch control capability
• Operate multiple devices directly from a PC or self powered USB hub
• Easily programmable for ATE applications
• Robust aluminum construction

Data Sheets