Products

Pulse and Universal Generator with 25 or 50MHz models, single or dual channel

TGP3100 Series

• TGP3121
• TGP3151
• TGP3122
• TGP3152

• Arbitrary waveforms at 800MS/s sampling rate and 16-bit vertical resolution
• Extensive internal/external modulation of all waveform types
• Linear and logarithmic sweeps of all waveform types
• Front panel mounted USB Flash drive interface
• GPIB (option), USB and LXI compliant LAN interfaces
• Triggered (burst count) or gated operation using internal or external trigger sources

• Arbitrary waveforms at 800MS/s sampling rate and 16-bit vertical resolution
• Extensive internal/external modulation of all waveform types
• Linear and logarithmic sweeps of all waveform types
• Front panel mounted USB Flash drive interface
• GPIB (option), USB and LXI compliant LAN interfaces
• Triggered (burst count) or gated operation using internal or external trigger sources

• Arbitrary waveforms at 800MS/s sampling rate and 16-bit vertical resolution
• Extensive internal/external modulation of all waveform types
• Linear and logarithmic sweeps of all waveform types
• Front panel mounted USB Flash drive interface
• GPIB (option), USB and LXI compliant LAN interfaces
• Triggered (burst count) or gated operation using internal or external trigger sources

• Arbitrary waveforms at 800MS/s sampling rate and 16-bit vertical resolution
• Extensive internal/external modulation of all waveform types
• Linear and logarithmic sweeps of all waveform types
• Front panel mounted USB Flash drive interface
• GPIB (option), USB and LXI compliant LAN interfaces
• Triggered (burst count) or gated operation using internal or external trigger sources

• Sine frequency up to 240MHz with 1µHz resolution
• Up to 100MHz high resolution pulse generator
• Arbitrary waveforms up to 16bits at 800MSa/s
• Wideband noise generator

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +12 to -12 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510 MCOR12 Power Modules are identical and interchangeable.
• Has two high-precision measurements of output current;
  • one is used to close the regulation control loop,
  • provides an independent monitoring signal to the Crate Interface Card.
• Fault sensing circuitry in the module sets a Fault Latch which inhibits the output.
• A (momentary) Sync input signal inhibits MOSFET switching when it is active (high);
  • this eliminate switching noise .
  • reduces power line noise during sensitive analog signal measurements.

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +30 to -30 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510R30 MCOR30 Power Modules are identical and interchangeable
  • Programming Card is plugged into the replacement module.
• Each channel has a critically-damped, LC noise filter with a cut-off frequency of about 8 kHz.
• A 16-pin front panel diagnostics connector taps onto major circuit nodes which enables quick “inthe-crate” fault evaluation

• 2U Chassis – 19″ rack mount 3.48” Height, 9.60” Depth and Weight 6lb.
• Power 120V AC 60Hz
• Washable front removable air filter
• Ball Bearing AC fans provide 330 CFM
• Dual plenum design
• Cooling for 160mm,220mm depth modules
• Diverts lower warmed air to rear of Cabinet
• RM option diverts lower air to front of Cabinet

• accommodate these control schemes
• total control system interface on a single VME-standard card
• occupies the left-most slot of the crate
• monitoring voltage reference inputs, output voltages and fault conditions
• standard VMEbus-compatible 6U by 220 mm board installed
• Eurocard crate
• Two 96-pin I/O connectors

MCOR Modules

MCOR 2/6/9/12

Each module can be customized to provide maximum outputs of 2 amps, 6 amps, 9 amps, and 12 amps. Up to 16 of these can fit in a single 6U VME style crate.

MCOR 30

Each module can provide a maximum output 30 amps. Up to 8 of these can fit in a single 6U VME style crate.

• On-wafer power device characterization up to 10,000 V DC / 600 A
• Reduced probe and device destruction at high currents up to 20 A DC and 300 A pulse
• Prevent thin wafers from curling and breaking
• Accurate Rds(on) measurement at high current
• Accurate UIS measurements at high temperature
• Roll-out stage for full wafer access and easy wafer loading/unloading
• Seamless integration between Velox and analyzers/measurement software
• High-throughput wafer autoloading (standard, thinned, warped, TAIKO)
• Easy on-screen navigation, wafer mapping, and operation of accessories with Velox

Enabling single-contact high-current/high-voltage test

• Enables coaxial measurements up to 10,000 V and 300 A pulsed (600 A in a parallel configuration) with a single touchdown
• Even distribution of high current with innovative multi-fingertip design
• Compatible with Tesla 200/300 mm power device characterization system
• Reduced measurement time by testing both high-voltage and high-current conditions with a single touchdown
• Accurate characterization of a wide range of pad sizes and test currents, with minimum pad damage and contact resistance
• Safe, reliable and repeatable high-current/voltage measurements over a wide temperature range (from -55°C to +300°C)

• provides precision bi-polar output currents
• minimal zero-cross over distortion
• 19” rack mounted 6U x 220 mm crate
• crate has 17 slots; 16 (slot 0 thru 15)
• connectors
  • J1 (ExtIntlk),
  • J2 (CrateOK),
  • J3 (Input Reference Voltages),
  • J4 (Output Monitors), and
  • J9 (Bitbus)

Positional current probe,  PCB track Touch & Measure

Unique technology enabling current measurement in PCB tracks bandwidth of DC to 5MHz, dynamic range of 10mA to 20A pk-pk useable with any normal oscilloscope, safety rated to 300V Cat II,  investigates waveforms in any conductor including ground planes.

Bench/System DC Power Supplies, PowerFlex or PowerFlex+ regulated Single or Dual Outputs 1200 watts, with/without Digital Remote Interfaces

• Single or dual outputs, 1200 watts total
• PowerFlex design gives variable voltage/current combinations within a power envelope
• Up to 60 volts or 80 volts and up to 50 amps
• Setting by direct numeric entry or by spin wheel
• High setting resolution of 1mV in up to 60 volts
• Low noise of < 3mV rms at full power
• Bench or rack mounting, front and rear terminals
• Quasi analogue remote control
• RS232, USB GPIB & LAN interfaces (P models)