Power Supplies, Signal Generators and Sources

with analogue and digital control, USB, RS232, LAN (LXI) and GPIB

• Versatile solution for direct testing of dc power sources and PFCs
• Constant current, resistance, conductance and power modes
• Wide voltage and current range, 10 to 500V and 0 to 16A
• 400 watts continuous dissipation at 28°C (360W at 40°C)
• High resolution and accuracy for level setting
• Built-in transient generator with variable slew
• Current monitor output for waveform viewing
• Variable drop-out voltage for battery testing
• High resolution backlit graphic LCD with soft key control
• Analogue remote control of levels and TTL control of on/off and transient switching
• Front and rear input terminals
• Load inputs rated to CAT II (300V)
• Full bus control via USB, RS232, GPIB and LXI compliant LAN interfaces

• Multiple ranges on each output for wider voltage/current choice
• Four independent 105W full performance outputs
• Instant individual on/off control plus sequencable multi on/off
• Simultaneous display of meters and settings for all outputs
• Up to 250 settings memories for individual or multiple outputs
• Instant access to voltage/current setting for any output
• USB, RS-232, LXI compliant LAN, and GPIB* interfaces (P versions)
• USB, RS-232, LXI compliant LAN, and GPIB* interfaces (P versions)
  Duplicate power and sense terminals at rear (P versions)

• Frequency up to 160MHz, 15 digits or 1µHz resolution
• Wideband noise generator | high resolution pulse generator
• Arbitrary waveforms up to 16bits at 800MS/s
• Comprehensive internal/external digital and analog modulations
• Two identical channels with phase control, coupling and tracking
• USB and LXI compliant LAN interfaces, plus optional GPIB interface

Pulse and Universal Generator with 25 or 50MHz models, single or dual channel

TGP3100 Series

• TGP3121
• TGP3151
• TGP3122
• TGP3152

• Arbitrary waveforms at 800MS/s sampling rate and 16-bit vertical resolution
• Extensive internal/external modulation of all waveform types
• Linear and logarithmic sweeps of all waveform types
• Front panel mounted USB Flash drive interface
• GPIB (option), USB and LXI compliant LAN interfaces
• Triggered (burst count) or gated operation using internal or external trigger sources

• Arbitrary waveforms at 800MS/s sampling rate and 16-bit vertical resolution
• Extensive internal/external modulation of all waveform types
• Linear and logarithmic sweeps of all waveform types
• Front panel mounted USB Flash drive interface
• GPIB (option), USB and LXI compliant LAN interfaces
• Triggered (burst count) or gated operation using internal or external trigger sources

• Arbitrary waveforms at 800MS/s sampling rate and 16-bit vertical resolution
• Extensive internal/external modulation of all waveform types
• Linear and logarithmic sweeps of all waveform types
• Front panel mounted USB Flash drive interface
• GPIB (option), USB and LXI compliant LAN interfaces
• Triggered (burst count) or gated operation using internal or external trigger sources

• Arbitrary waveforms at 800MS/s sampling rate and 16-bit vertical resolution
• Extensive internal/external modulation of all waveform types
• Linear and logarithmic sweeps of all waveform types
• Front panel mounted USB Flash drive interface
• GPIB (option), USB and LXI compliant LAN interfaces
• Triggered (burst count) or gated operation using internal or external trigger sources

• Sine frequency up to 240MHz with 1µHz resolution
• Up to 100MHz high resolution pulse generator
• Arbitrary waveforms up to 16bits at 800MSa/s
• Wideband noise generator

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +12 to -12 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510 MCOR12 Power Modules are identical and interchangeable.
• Has two high-precision measurements of output current;
  • one is used to close the regulation control loop,
  • provides an independent monitoring signal to the Crate Interface Card.
• Fault sensing circuitry in the module sets a Fault Latch which inhibits the output.
• A (momentary) Sync input signal inhibits MOSFET switching when it is active (high);
  • this eliminate switching noise .
  • reduces power line noise during sensitive analog signal measurements.

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +30 to -30 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510R30 MCOR30 Power Modules are identical and interchangeable
  • Programming Card is plugged into the replacement module.
• Each channel has a critically-damped, LC noise filter with a cut-off frequency of about 8 kHz.
• A 16-pin front panel diagnostics connector taps onto major circuit nodes which enables quick “inthe-crate” fault evaluation

Enabling single-contact high-current/high-voltage test

• Enables coaxial measurements up to 10,000 V and 300 A pulsed (600 A in a parallel configuration) with a single touchdown
• Even distribution of high current with innovative multi-fingertip design
• Compatible with Tesla 200/300 mm power device characterization system
• Reduced measurement time by testing both high-voltage and high-current conditions with a single touchdown
• Accurate characterization of a wide range of pad sizes and test currents, with minimum pad damage and contact resistance
• Safe, reliable and repeatable high-current/voltage measurements over a wide temperature range (from -55°C to +300°C)

• compact and completely modular design
• high effectiveness in all operation modes, few requirements on building infrastructure
• ability to use an existing liquid cooling system directly
• optional matched liquid-to-air cooling unit TC.LAE available
• possibility of upgrading to systems of up to 1 MVA
• high level of system dynamics, ≤ 5 kHz modulation bandwidth
• non-restrictive capability of refeeding in the Q4 operation mode
• possibility of operating as an autonomous 4-Q and 3-phase quasi-analogue amplifier
• possibility of “Hardware-in-the loop”-operation (HIL mode)
• user friendly application software with pre-configured test patterns
• possibility of integrating into a complete SAS simulation and test system
• galvanic isolation available as an option without derating the simulator port data

Bidirectional (source & sink), Regenerative 0…65VDC to 0…1500VDC, 20kW up to 1.5 MW 

• cell system nominal voltage and type of chemistry
• number of cells
• internal resistance and associated parameters
• cell temperature progression
• allowed current
• charge efficiency
• energy computing and management facilities
• time-dependent and functional dependent parameters

• Setting of operational parameters for each output phase: (frequency, phase, voltage, basic waveform)
• Defining functional blocks enabling a wide variety of modulation capabilities
• Defining, editing and storing of even complex and long test sequences
• Preview window for output voltage waveforms
• LC load mode, definition of complex equivalent circuits
• Hand drawing curve tool and FOURIER tool (harmonics synthesis)
• TC.ACS provides an extensive safety concept in order to detect unwanted or off-limit conditions very quickly and to initiate controlled limiting or even a shutdown.