Products

The AZX Series (Regenerative AC / DC Power Source) is a family of high power, single, split and three phase, AC, DC and AC+DC output capable Power Sources with full energy recovery to the AC mains when sinking power from the equipment under test. Available models range from 30 kVA to 440 kVA. Using a modern color touch screen based user interface for ease of use, the AZX Series is cost effective and fully programmable for both basic frequency conversion and advanced AC power line or DC power disturbance test applications requiring up to 1000 Hz fundamental frequency.

The energy recovery capability allows both sourcing and sinking of current and power up to 100% of rated power. Adding the Load Option (Option L) adds full electronic regenerative AC & DC Load programming capability to the AZX.

• High-Speed Current Control: No dynamic overshoot or oscillation
• High Slew-Rate: Up to 30A/*s for fast load changes
• Low Voltage Operation: Stable operation with no turn-on delay
• Multi-Functional: Seven load modes and four operating modes
• Parallel Operation: Up to 10kW with 10 units
• User-Friendly Interface: Built-in USB and optional IEEE interfaces
• Compliance: EN61010-1 compliant with a two-year warranty

• Protocol reports
• Generation of waveforms with synchronous data acquisition
• Modular Expandable
• Individual Waveform Generation
• Standard Libraries included
• Unlimited Waveform size
• 2 different Waveforms synchronously
• DLL’s for LabView, Vector CANoe / CAPL, C#, C++, ANSI C, Python, etc.
• Simulation of imported oscilloscope waveform

BOLAB revolutionizes EV testing with powerful, flexible, and modular HV Electric Vehicle Test Systems. These solutions offer high-speed testing, covering diverse profiles and budgets. Features include a modular design, adaptability, and WaveMaster Software for custom waveforms. Benefit from efficiency, precision, and cost-efficiency in EV testing. Discover the future of high-speed testing with BOLAB’s innovative solutions.

The new G5.RSS series features

• High control dynamics
• An exceptional accuracy
• A nominal output voltage of up to 3000 VDC
• A wide current-voltage range with an auto-ranging factor of 3.
• You get the best value for your investment.

Key Performance Capabilities:

• Slew rates up to 60 V/µsec.
• Up to 240A DC at +50VDC or –50VDC (4301-240 configuration).
• Can provide pulses of up to 800 amps at voltages of up to ±100V (4301-240 configuration).
• Adjustable compensation allows the system to maintain a 50V/2 µsec rise-time over a wide range of current outputs.

Key Performance Capabilities:

• 4-Quadrant – Can source and sink current
• ±80V – DC supply for 12V to 48V systems; meets 80V surge requirements
• 300 kHz Sine – DC ripple tests for all major standards
• 3µs Rise Time – Exceeds surge and dropout slew rate requirements
• 3mΩ DC Source Impedance – Out-performs ISO 7637-2 requirements
• Supports ground reference and supply offset testing required for ISO 16750-2 Sect. 4.8 and other similar standards

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +12 to -12 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510 MCOR12 Power Modules are identical and interchangeable.
• Has two high-precision measurements of output current;
  • one is used to close the regulation control loop,
  • provides an independent monitoring signal to the Crate Interface Card.
• Fault sensing circuitry in the module sets a Fault Latch which inhibits the output.
• A (momentary) Sync input signal inhibits MOSFET switching when it is active (high);
  • this eliminate switching noise .
  • reduces power line noise during sensitive analog signal measurements.

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +30 to -30 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510R30 MCOR30 Power Modules are identical and interchangeable
  • Programming Card is plugged into the replacement module.
• Each channel has a critically-damped, LC noise filter with a cut-off frequency of about 8 kHz.
• A 16-pin front panel diagnostics connector taps onto major circuit nodes which enables quick “inthe-crate” fault evaluation

• Frequency Range 10 Hz – 1GHz, 3GHz or 6GHz
• 4000x faster in your pre-certifcation work
• compact design and +12V power supply
• 162.5 MHz full gapless real-time analysis bandwidth
• Weighted Real-time Spectrogram

• requency Range from DC up to 40 GHz
• 685 MHz Real-time analysis bandwidth
• Dynamic range of more than 100 dB
• Multi-GHz real-time scanning up to 40 GHz
• all 6dB RBWs acc. to CISPR, MIL, DO, ANSI, FCC
• fastest super-heterodyn receiver on the planet

• Dynamic set up: During a simple frame reading, users can define elements to be acquired, recorded, visualized and surveyed in real time.
•  Macro-command: Users can write and execute complex test sequences thanks to macro-command functions.
•  Local & Distant Integration: AT-DIAG can be driven and interrogated by external software. It can also be used with a computer through Ethernet.
• Communication ports: Communication is done through RS232, NI CAN acq. Card, specific acquisition card or system.
•  Protocols: FREERUNNING, KWP2000, CAN, LIN, FlexRay, ARINC, … Possibility to implement new protocols (customized protocol, …).
•  Multi-product & Multi-protocol Communication: Communication can be set up with multiple addresses and protocols during a single test.

• 1 software for all your equipment
• 1 software for all standards
• 1 software for your electrical and EMC tests
• Advanced functions of monitoring and control
• Automated reports
• Team of specialists at your disposal

• Fast: ACA compression and parallelization allow to speed up the calculation
• Accurate: Fully validated with measurement results on real mock-up
• Innovative: New method from research labs
• Powerful: Compute very large models
• Easy: Dedicated graphical user interface with modern layout

• Fast: ACA compression and parallelization allow to speed up the calculation
• Accurate: Fully validated with measurement results on real mock-up
• Innovative: New method from research labs
• Powerful: Compute very large models
• Easy: Dedicated graphical user interface with modern layout

• Unique user interface for all tests
• Independent from any measuring device manufacturers
• Free drivers and over 500 supported devices
• Efficient and dedicated Technical support
• Wide range of supported standards (ENxx, CISPR, AUTOMOTIVE, DO160, …)
• Interface Agilent VEE™, WindowsLabView™, LabWindows CVI™, Visual C++
• Operating system: Win XP, Vista, Seven, Windows 8
• Report in MS Office™ 2003, 2007, 2010, 2013, Open office