Products

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +12 to -12 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510 MCOR12 Power Modules are identical and interchangeable.
• Has two high-precision measurements of output current;
  • one is used to close the regulation control loop,
  • provides an independent monitoring signal to the Crate Interface Card.
• Fault sensing circuitry in the module sets a Fault Latch which inhibits the output.
• A (momentary) Sync input signal inhibits MOSFET switching when it is active (high);
  • this eliminate switching noise .
  • reduces power line noise during sensitive analog signal measurements.

• Proven member of a modular Power Module family, more than 800 units are in service
• Precision-regulated Bi-Polar output provides up to +30 to -30 Amps for Magnet loads.
• Smooth operation through zero amps output current, no “Crossover” problems.
• All 2510R30 MCOR30 Power Modules are identical and interchangeable
  • Programming Card is plugged into the replacement module.
• Each channel has a critically-damped, LC noise filter with a cut-off frequency of about 8 kHz.
• A 16-pin front panel diagnostics connector taps onto major circuit nodes which enables quick “inthe-crate” fault evaluation

• 2U Chassis – 19″ rack mount 3.48” Height, 9.60” Depth and Weight 6lb.
• Power 120V AC 60Hz
• Washable front removable air filter
• Ball Bearing AC fans provide 330 CFM
• Dual plenum design
• Cooling for 160mm,220mm depth modules
• Diverts lower warmed air to rear of Cabinet
• RM option diverts lower air to front of Cabinet

• accommodate these control schemes
• total control system interface on a single VME-standard card
• occupies the left-most slot of the crate
• monitoring voltage reference inputs, output voltages and fault conditions
• standard VMEbus-compatible 6U by 220 mm board installed
• Eurocard crate
• Two 96-pin I/O connectors

MCOR Modules

MCOR 2/6/9/12

Each module can be customized to provide maximum outputs of 2 amps, 6 amps, 9 amps, and 12 amps. Up to 16 of these can fit in a single 6U VME style crate.

MCOR 30

Each module can provide a maximum output 30 amps. Up to 8 of these can fit in a single 6U VME style crate.

• provides precision bi-polar output currents
• minimal zero-cross over distortion
• 19” rack mounted 6U x 220 mm crate
• crate has 17 slots; 16 (slot 0 thru 15)
• connectors
  • J1 (ExtIntlk),
  • J2 (CrateOK),
  • J3 (Input Reference Voltages),
  • J4 (Output Monitors), and
  • J9 (Bitbus)

High‐Resolution Portable TDR with Frequency‐Domain Analysis Tools

Ideal for testing all types of microwave/RF and digital cables and connectors

• Rugged portable TDR with S‐parameter tools
• Resolves connector detail (<1 cm)
• 75 μm (0.003 in.) cursor resolution
• 16‐bit digital sampling at up to 250 KSPS
• Stores thousands of TDR traces
• USB host/client, 10/100 Ethernet
• Lightweight, bright color screen
• Internet streaming and remote control

Simplify Aging Aircraft Wiring Maintenance Using High-Resolution MOHR CT100 Series TDR Cable Analyzers

• Designed for use with the high-resolution CT100 TDR Cable Tester
• Ideal for TDR testing MIL-STD-1553B data bus aerospace cable assemblies
• Detect and localize open, short, and partial cable and connector faults on the main bus and stubs
• Detects cable and connector faults through 3+ transformer couplers
• Simplifies troubleshooting of aging aircraft MIL-STD-1553 cable assemblies

• Dynamic set up: During a simple frame reading, users can define elements to be acquired, recorded, visualized and surveyed in real time.
•  Macro-command: Users can write and execute complex test sequences thanks to macro-command functions.
•  Local & Distant Integration: AT-DIAG can be driven and interrogated by external software. It can also be used with a computer through Ethernet.
• Communication ports: Communication is done through RS232, NI CAN acq. Card, specific acquisition card or system.
•  Protocols: FREERUNNING, KWP2000, CAN, LIN, FlexRay, ARINC, … Possibility to implement new protocols (customized protocol, …).
•  Multi-product & Multi-protocol Communication: Communication can be set up with multiple addresses and protocols during a single test.

• 1 software for all your equipment
• 1 software for all standards
• 1 software for your electrical and EMC tests
• Advanced functions of monitoring and control
• Automated reports
• Team of specialists at your disposal

• Fast: ACA compression and parallelization allow to speed up the calculation
• Accurate: Fully validated with measurement results on real mock-up
• Innovative: New method from research labs
• Powerful: Compute very large models
• Easy: Dedicated graphical user interface with modern layout

• Fast: ACA compression and parallelization allow to speed up the calculation
• Accurate: Fully validated with measurement results on real mock-up
• Innovative: New method from research labs
• Powerful: Compute very large models
• Easy: Dedicated graphical user interface with modern layout

• Unique user interface for all tests
• Independent from any measuring device manufacturers
• Free drivers and over 500 supported devices
• Efficient and dedicated Technical support
• Wide range of supported standards (ENxx, CISPR, AUTOMOTIVE, DO160, …)
• Interface Agilent VEE™, WindowsLabView™, LabWindows CVI™, Visual C++
• Operating system: Win XP, Vista, Seven, Windows 8
• Report in MS Office™ 2003, 2007, 2010, 2013, Open office

• 16K Video Generator & Analyzer
• Dolby Vision™, HDR 10 and HDR 10+
• validating DP 1.4a & DP 2.0 Link Layer on DP Sinks and Sources
• Power Input +12 Vdc (AC/DC converter included)
• Module Size/Weight TBD for Weight and Size

• Compact sized DisplayPort™ 1.2 compliant Reference Sink
• HBR2 and MST capable Sink and Branch device
• Cerified as the platform for DP 1.2 LL CTS Ext1 tests
• Optional MST Debug panel and AUX Channel Monitor
• Debug and Test Controller GUI enables monitoring and previewing any MST stream
• User programmable EDID and DPCD

•  HDMI 2.1 Test Equipment (FRL)
• Enhanced Gaming Features (VRR, ALLM)
• FEC, Forward Error Correction
• HDCP 2.2 & HDCP 2.3 support  TMDS Support
• Dolby Vision™ Test Tool
• 8K@60 fps Support (12 Gbps/channel)
• eARC Support (end of 2019)
• DSC Support (ESTIMATED 2020)
• UCD Console GUI for debugging
• High level API for easy integreation